Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/5
    1. Worker rights, employer duties and reporting hazards
    2. The hierarchy of controls and personal protective equipment
    3. Lockout/tagout, machine guarding and electrical hazards
    4. Hazard communication, chemical storage and fire
    5. Confined spaces and ergonomics
  2. 2.Quality Practices & Inspection0/4
    1. Quality systems, audits and the internal customer
    2. Prevention versus detection: cost of quality and inspection points
    3. Control charts and variation
    4. Root cause tools, nonconforming product and corrective action
  3. 3.Measurement & Blueprint Reading0/5
    1. Choosing and reading micrometers and calipers
    2. Indicators, transfer gauges and go/no-go gauges
    3. Calibration and conditions that affect accuracy
    4. Reading the print: views, lines, scale and the title block
    5. Limits, tolerance, allowance and GD&T basics
  4. 4.Manufacturing Processes & Materials0/5
    1. How parts are shaped: casting, molding, forging, machining and additive
    2. Joining, heat treating and finishing
    3. Materials and their properties
    4. Volume, setup cost, takt time and the bottleneck
    5. Work orders, travelers, traceability and connected machines
  5. 5.Lean & Continuous Improvement0/5
    1. Value-added, non-value-added and necessary work
    2. The eight wastes
    3. 5S, visual management and the andon
    4. Standard work, kaizen and plan-do-check-act
    5. Pull, value stream maps, quick changeover and poka-yoke
  6. 6.Maintenance Awareness0/5
    1. Reactive, preventive and predictive maintenance, and TPM
    2. PM discipline, maintenance records and warning signs
    3. Lockout/tagout and stored energy
    4. Lubrication, bearings and shaft alignment
    5. Belts, chains, motor overloads and fluid power
Saved in this browser. Move it to another device →
← Back

Study guide · Chapter 4 of 6

Manufacturing Processes & Materials Study Guide — Production Technician

28 free practice questions

This chapter covers the process and materials half of the MSSC Manufacturing Processes & Production module: how parts are shaped, joined and finished, what the common materials do, and how a job is paced, documented and traced through the plant. Questions usually describe a part or a shop-floor situation and ask which process fits or what the technician should do. You need the reason behind each choice, not memorized machine settings.

Key takeaways

  • Casting and molding fill a cavity, forging and stamping deform solid material, machining removes chips, and additive manufacturing builds in layers.
  • Expensive tooling such as dies and molds only pays off when high volume spreads its fixed cost over many parts.
  • Takt time is available production time divided by customer demand, and the slowest station sets the real output of a line.
  • If material does not match the work order, stop and tell the supervisor before running anything.
  • Lot numbers scanned at each step give traceability, and connected sensors help catch problems before failure, but neither replaces procedures or records.

Lessons in this chapter

5 short lessons · 5 min read

  1. 1How parts are shaped: casting, molding, forging, machining and additive1 min
  2. 2Joining, heat treating and finishing1 min
  3. 3Materials and their properties1 min
  4. 4Volume, setup cost, takt time and the bottleneck1 min
  5. 5Work orders, travelers, traceability and connected machines1 min
View all questions & answers →

Facts checked 2026-11-15 · Sources: MSSC: Certified Production Technician (CPT 4.0)

Production Technician cheat sheet: every key fact on one page →Next chapter: Lean & Continuous Improvement →

Practice questions based on the MSSC Production Standards and the published content of the Certified Production Technician modules, together with federal OSHA general-industry requirements and standard manufacturing practice. MSSC and CPT are marks of the Manufacturing Skills Standards Council; this site is not affiliated with or endorsed by MSSC. Questions here never depend on recalling a regulatory limit, a citation number or a machine specification — always follow your own facility's written programs and the manufacturer's documentation for the equipment you run, and confirm current requirements before testing. About the CPT certification →