Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/5
    1. Worker rights, employer duties and reporting hazards
    2. The hierarchy of controls and personal protective equipment
    3. Lockout/tagout, machine guarding and electrical hazards
    4. Hazard communication, chemical storage and fire
    5. Confined spaces and ergonomics
  2. 2.Quality Practices & Inspection0/4
    1. Quality systems, audits and the internal customer
    2. Prevention versus detection: cost of quality and inspection points
    3. Control charts and variation
    4. Root cause tools, nonconforming product and corrective action
  3. 3.Measurement & Blueprint Reading0/5
    1. Choosing and reading micrometers and calipers
    2. Indicators, transfer gauges and go/no-go gauges
    3. Calibration and conditions that affect accuracy
    4. Reading the print: views, lines, scale and the title block
    5. Limits, tolerance, allowance and GD&T basics
  4. 4.Manufacturing Processes & Materials0/5
    1. How parts are shaped: casting, molding, forging, machining and additive
    2. Joining, heat treating and finishing
    3. Materials and their properties
    4. Volume, setup cost, takt time and the bottleneck
    5. Work orders, travelers, traceability and connected machines
  5. 5.Lean & Continuous Improvement0/5
    1. Value-added, non-value-added and necessary work
    2. The eight wastes
    3. 5S, visual management and the andon
    4. Standard work, kaizen and plan-do-check-act
    5. Pull, value stream maps, quick changeover and poka-yoke
  6. 6.Maintenance Awareness0/5
    1. Reactive, preventive and predictive maintenance, and TPM
    2. PM discipline, maintenance records and warning signs
    3. Lockout/tagout and stored energy
    4. Lubrication, bearings and shaft alignment
    5. Belts, chains, motor overloads and fluid power
Saved in this browser. Move it to another device →
← Back

Study guide · Chapter 1 of 6

Safety Study Guide — Production Technician

30 free practice questions

The Safety module of the MSSC Certified Production Technician program asks what a front-line worker should do when a hazard, a machine, a chemical or an emergency is in front of them. Most questions describe a short shop-floor scene and ask for the correct decision, so the goal is to know the safe action and the reason it ranks above the tempting shortcut. The duties below come from federal OSHA general-industry rules, NIOSH guidance and the MSSC Safety module outline.

Key takeaways

  • Report hazards and near misses through the company procedure, and know that federal law forbids punishing a worker for reporting.
  • The hierarchy of controls runs elimination, substitution, engineering, administrative, then PPE, and the higher control is the better answer.
  • After locking and tagging a machine, release stored energy and verify zero energy before any work begins, and remove only your own lock.
  • Every workplace chemical container needs the product identity and hazard information, and the safety data sheet must be reachable on every shift.
  • A confined-space attendant stays outside and calls trained rescue, because would-be rescuers are often overcome by the same atmosphere.

Lessons in this chapter

5 short lessons · 5 min read

  1. 1Worker rights, employer duties and reporting hazards1 min
  2. 2The hierarchy of controls and personal protective equipment1 min
  3. 3Lockout/tagout, machine guarding and electrical hazards1 min
  4. 4Hazard communication, chemical storage and fire1 min
  5. 5Confined spaces and ergonomics1 min
View all questions & answers →

Facts checked 2026-11-15 · Sources: MSSC: Certified Production Technician (CPT 4.0), OSHA 29 CFR 1910.147: The control of hazardous energy (lockout/tagout), OSHA: Hazard Communication

Production Technician cheat sheet: every key fact on one page →Next chapter: Quality Practices & Inspection →

Practice questions based on the MSSC Production Standards and the published content of the Certified Production Technician modules, together with federal OSHA general-industry requirements and standard manufacturing practice. MSSC and CPT are marks of the Manufacturing Skills Standards Council; this site is not affiliated with or endorsed by MSSC. Questions here never depend on recalling a regulatory limit, a citation number or a machine specification — always follow your own facility's written programs and the manufacturer's documentation for the equipment you run, and confirm current requirements before testing. About the CPT certification →