Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/5
    1. Worker rights, employer duties and reporting hazards
    2. The hierarchy of controls and personal protective equipment
    3. Lockout/tagout, machine guarding and electrical hazards
    4. Hazard communication, chemical storage and fire
    5. Confined spaces and ergonomics
  2. 2.Quality Practices & Inspection0/4
    1. Quality systems, audits and the internal customer
    2. Prevention versus detection: cost of quality and inspection points
    3. Control charts and variation
    4. Root cause tools, nonconforming product and corrective action
  3. 3.Measurement & Blueprint Reading0/5
    1. Choosing and reading micrometers and calipers
    2. Indicators, transfer gauges and go/no-go gauges
    3. Calibration and conditions that affect accuracy
    4. Reading the print: views, lines, scale and the title block
    5. Limits, tolerance, allowance and GD&T basics
  4. 4.Manufacturing Processes & Materials0/5
    1. How parts are shaped: casting, molding, forging, machining and additive
    2. Joining, heat treating and finishing
    3. Materials and their properties
    4. Volume, setup cost, takt time and the bottleneck
    5. Work orders, travelers, traceability and connected machines
  5. 5.Lean & Continuous Improvement0/5
    1. Value-added, non-value-added and necessary work
    2. The eight wastes
    3. 5S, visual management and the andon
    4. Standard work, kaizen and plan-do-check-act
    5. Pull, value stream maps, quick changeover and poka-yoke
  6. 6.Maintenance Awareness0/5
    1. Reactive, preventive and predictive maintenance, and TPM
    2. PM discipline, maintenance records and warning signs
    3. Lockout/tagout and stored energy
    4. Lubrication, bearings and shaft alignment
    5. Belts, chains, motor overloads and fluid power
Saved in this browser. Move it to another device →
← Measurement & Blueprint Reading

Chapter 3 · Lesson 2 of 5

Indicators, transfer gauges and go/no-go gauges

1 min read

Not every gauge reads size directly, and exam questions test whether you know what each one actually reports. Sorting them into three families makes the answers easy to spot.

GaugeWhat it tells you
Dial indicatorHow far a surface departs from a reference zero set on a master or gauge block
Telescoping or small-hole gaugeNothing by itself; it is locked in the bore and then read with an outside micrometer
Go/no-go plug gaugeAccept or reject only; no actual dimension
Feeler gaugeThe clearance in a narrow gap, from the blade that slides through with light drag

A hole passes a plug gauge check when the GO member enters and the NO-GO member does not. The GO end is made to the maximum material limit, the smallest allowed hole, and the NO-GO end to the other limit, so passing both proves the hole is between its limits.

Example: if the NO-GO end slips into a bore, the hole is oversize and the part is rejected even though the GO end also fits. Because an indicator only shows deviation from its zero, the zero must be confirmed on the master before any part is judged.

Feeler example: if the 0.004 in blade slides through with light drag and the 0.005 in blade will not enter, the gap is about 0.004 in.

Check yourself

1. A hole is checked with a go/no-go plug gauge. The part is accepted when which condition is met?

2. A dial indicator is mounted on a stand and swept across a machined surface. What does the reading actually tell the inspector?

Facts checked 2026-11-15 · Sources: MSSC: Certified Production Technician (CPT 4.0), NIST: Metrological traceability

Production Technician cheat sheet: every key fact on one page →