Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/5
    1. Worker rights, employer duties and reporting hazards
    2. The hierarchy of controls and personal protective equipment
    3. Lockout/tagout, machine guarding and electrical hazards
    4. Hazard communication, chemical storage and fire
    5. Confined spaces and ergonomics
  2. 2.Quality Practices & Inspection0/4
    1. Quality systems, audits and the internal customer
    2. Prevention versus detection: cost of quality and inspection points
    3. Control charts and variation
    4. Root cause tools, nonconforming product and corrective action
  3. 3.Measurement & Blueprint Reading0/5
    1. Choosing and reading micrometers and calipers
    2. Indicators, transfer gauges and go/no-go gauges
    3. Calibration and conditions that affect accuracy
    4. Reading the print: views, lines, scale and the title block
    5. Limits, tolerance, allowance and GD&T basics
  4. 4.Manufacturing Processes & Materials0/5
    1. How parts are shaped: casting, molding, forging, machining and additive
    2. Joining, heat treating and finishing
    3. Materials and their properties
    4. Volume, setup cost, takt time and the bottleneck
    5. Work orders, travelers, traceability and connected machines
  5. 5.Lean & Continuous Improvement0/5
    1. Value-added, non-value-added and necessary work
    2. The eight wastes
    3. 5S, visual management and the andon
    4. Standard work, kaizen and plan-do-check-act
    5. Pull, value stream maps, quick changeover and poka-yoke
  6. 6.Maintenance Awareness0/5
    1. Reactive, preventive and predictive maintenance, and TPM
    2. PM discipline, maintenance records and warning signs
    3. Lockout/tagout and stored energy
    4. Lubrication, bearings and shaft alignment
    5. Belts, chains, motor overloads and fluid power
Saved in this browser. Move it to another device →
← Back

Study guide · Chapter 6 of 6

Maintenance Awareness Study Guide — Production Technician

22 free practice questions

The Maintenance Awareness module checks that a production technician can keep equipment healthy, spot trouble early and know when to hand a problem to maintenance. Questions cover maintenance strategies, records, lockout, lubrication, drives, motors and fluid power, almost always as a situation with a right next step. Torque values and lubrication intervals differ from machine to machine, so the permanent rule is to follow the machine's own documentation and the plant's procedures.

Key takeaways

  • Reactive maintenance waits for failure, preventive works on a schedule, and predictive trends a measured condition such as vibration.
  • A PM is complete only when it is recorded, and a PM that cannot be done on time is escalated for rescheduling, never skipped or signed in advance.
  • Under lockout, each worker's lock is removed only by that worker, and stored energy is relieved and zero energy verified before work starts.
  • Contamination and wrong lubrication, too little or too much, are leading causes of early bearing failure.
  • A tripping overload relay is a symptom to investigate, and a hydraulic pump makes flow while pressure comes from resistance.

Lessons in this chapter

5 short lessons · 5 min read

  1. 1Reactive, preventive and predictive maintenance, and TPM1 min
  2. 2PM discipline, maintenance records and warning signs1 min
  3. 3Lockout/tagout and stored energy1 min
  4. 4Lubrication, bearings and shaft alignment1 min
  5. 5Belts, chains, motor overloads and fluid power1 min
View all questions & answers →

Facts checked 2026-11-15 · Sources: MSSC: Certified Production Technician (CPT 4.0), OSHA 29 CFR 1910.147: The control of hazardous energy (lockout/tagout)

Production Technician cheat sheet: every key fact on one page →

Practice questions based on the MSSC Production Standards and the published content of the Certified Production Technician modules, together with federal OSHA general-industry requirements and standard manufacturing practice. MSSC and CPT are marks of the Manufacturing Skills Standards Council; this site is not affiliated with or endorsed by MSSC. Questions here never depend on recalling a regulatory limit, a citation number or a machine specification — always follow your own facility's written programs and the manufacturer's documentation for the equipment you run, and confirm current requirements before testing. About the CPT certification →