Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/5
    1. Worker rights, employer duties and reporting hazards
    2. The hierarchy of controls and personal protective equipment
    3. Lockout/tagout, machine guarding and electrical hazards
    4. Hazard communication, chemical storage and fire
    5. Confined spaces and ergonomics
  2. 2.Quality Practices & Inspection0/4
    1. Quality systems, audits and the internal customer
    2. Prevention versus detection: cost of quality and inspection points
    3. Control charts and variation
    4. Root cause tools, nonconforming product and corrective action
  3. 3.Measurement & Blueprint Reading0/5
    1. Choosing and reading micrometers and calipers
    2. Indicators, transfer gauges and go/no-go gauges
    3. Calibration and conditions that affect accuracy
    4. Reading the print: views, lines, scale and the title block
    5. Limits, tolerance, allowance and GD&T basics
  4. 4.Manufacturing Processes & Materials0/5
    1. How parts are shaped: casting, molding, forging, machining and additive
    2. Joining, heat treating and finishing
    3. Materials and their properties
    4. Volume, setup cost, takt time and the bottleneck
    5. Work orders, travelers, traceability and connected machines
  5. 5.Lean & Continuous Improvement0/5
    1. Value-added, non-value-added and necessary work
    2. The eight wastes
    3. 5S, visual management and the andon
    4. Standard work, kaizen and plan-do-check-act
    5. Pull, value stream maps, quick changeover and poka-yoke
  6. 6.Maintenance Awareness0/5
    1. Reactive, preventive and predictive maintenance, and TPM
    2. PM discipline, maintenance records and warning signs
    3. Lockout/tagout and stored energy
    4. Lubrication, bearings and shaft alignment
    5. Belts, chains, motor overloads and fluid power
Saved in this browser. Move it to another device →
← Maintenance Awareness

Chapter 6 · Lesson 5 of 5

Belts, chains, motor overloads and fluid power

1 min read

Belt tension is checked by deflection. A common rule is 1/64 inch of deflection per inch of span, under the force the drive maker specifies. Example: a 40-inch span gives 40 ÷ 64 = 5/8 inch.

A loose belt slips, overheats and glazes its sidewalls; an over-tight belt overloads the shafts and bearings. A roller chain that has stretched is really worn at each pin and bushing, so a worn chain is replaced along with its sprockets rather than patched with new links.

In a motor starter, fuses and breakers protect the wiring from short circuits and act very fast at very high current. The overload relay is sized to the motor and trips on a smaller, sustained overcurrent that would slowly cook the windings.

An overload that trips repeatedly is telling you something is wrong, such as a jam, a failing bearing, low voltage or a lost phase, so stop the motor and have the cause found.

In hydraulics, the pump creates flow; pressure rises only when that flow meets resistance. The relief valve caps maximum pressure and the directional valve routes flow. Milky oil that stays hazy after standing points to water, while foam that clears points to air. In pneumatics, water collects in the filter bowl and is drained on the PM schedule.

Check yourself

1. Which statement about a hydraulic system is correct?

2. A motor's overload relay has tripped three times during one shift. What should be done?

Facts checked 2026-11-15 · Sources: MSSC: Certified Production Technician (CPT 4.0), OSHA 29 CFR 1910.147: The control of hazardous energy (lockout/tagout)

Production Technician cheat sheet: every key fact on one page →