Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/5
    1. Worker rights, employer duties and reporting hazards
    2. The hierarchy of controls and personal protective equipment
    3. Lockout/tagout, machine guarding and electrical hazards
    4. Hazard communication, chemical storage and fire
    5. Confined spaces and ergonomics
  2. 2.Quality Practices & Inspection0/4
    1. Quality systems, audits and the internal customer
    2. Prevention versus detection: cost of quality and inspection points
    3. Control charts and variation
    4. Root cause tools, nonconforming product and corrective action
  3. 3.Measurement & Blueprint Reading0/5
    1. Choosing and reading micrometers and calipers
    2. Indicators, transfer gauges and go/no-go gauges
    3. Calibration and conditions that affect accuracy
    4. Reading the print: views, lines, scale and the title block
    5. Limits, tolerance, allowance and GD&T basics
  4. 4.Manufacturing Processes & Materials0/5
    1. How parts are shaped: casting, molding, forging, machining and additive
    2. Joining, heat treating and finishing
    3. Materials and their properties
    4. Volume, setup cost, takt time and the bottleneck
    5. Work orders, travelers, traceability and connected machines
  5. 5.Lean & Continuous Improvement0/5
    1. Value-added, non-value-added and necessary work
    2. The eight wastes
    3. 5S, visual management and the andon
    4. Standard work, kaizen and plan-do-check-act
    5. Pull, value stream maps, quick changeover and poka-yoke
  6. 6.Maintenance Awareness0/5
    1. Reactive, preventive and predictive maintenance, and TPM
    2. PM discipline, maintenance records and warning signs
    3. Lockout/tagout and stored energy
    4. Lubrication, bearings and shaft alignment
    5. Belts, chains, motor overloads and fluid power
Saved in this browser. Move it to another device →
← Back

Study guide · Chapter 3 of 6

Measurement & Blueprint Reading Study Guide — Production Technician

22 free practice questions

This chapter covers the measurement half of the MSSC Quality Practices and Measurement module: choosing and reading precision instruments, keeping them accurate, and reading the drawing that says what to measure. Unlike most of the CPT, these questions often include numbers, but the stem always supplies them, so the skill is applying a reading or a tolerance correctly. Work every example below by hand before checking the answer.

Key takeaways

  • By the rule of ten, the instrument should resolve about one tenth of the tolerance being checked.
  • An inch micrometer reading is the numbered sleeve value plus each exposed 0.025 in step plus the thimble thousandths.
  • Indicators compare to a zero, transfer gauges need a micrometer to read them, and go/no-go gauges only accept or reject.
  • When a gauge fails calibration, every part measured since its last good calibration is suspect and is re-inspected.
  • Never scale a print; an untoleranced dimension takes the title-block default for its number of decimal places.

Lessons in this chapter

5 short lessons · 5 min read

  1. 1Choosing and reading micrometers and calipers1 min
  2. 2Indicators, transfer gauges and go/no-go gauges1 min
  3. 3Calibration and conditions that affect accuracy1 min
  4. 4Reading the print: views, lines, scale and the title block1 min
  5. 5Limits, tolerance, allowance and GD&T basics1 min
View all questions & answers →

Facts checked 2026-11-15 · Sources: MSSC: Certified Production Technician (CPT 4.0), NIST: Metrological traceability

Production Technician cheat sheet: every key fact on one page →Next chapter: Manufacturing Processes & Materials →

Practice questions based on the MSSC Production Standards and the published content of the Certified Production Technician modules, together with federal OSHA general-industry requirements and standard manufacturing practice. MSSC and CPT are marks of the Manufacturing Skills Standards Council; this site is not affiliated with or endorsed by MSSC. Questions here never depend on recalling a regulatory limit, a citation number or a machine specification — always follow your own facility's written programs and the manufacturer's documentation for the equipment you run, and confirm current requirements before testing. About the CPT certification →