Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/5
    1. Worker rights, employer duties and reporting hazards
    2. The hierarchy of controls and personal protective equipment
    3. Lockout/tagout, machine guarding and electrical hazards
    4. Hazard communication, chemical storage and fire
    5. Confined spaces and ergonomics
  2. 2.Quality Practices & Inspection0/4
    1. Quality systems, audits and the internal customer
    2. Prevention versus detection: cost of quality and inspection points
    3. Control charts and variation
    4. Root cause tools, nonconforming product and corrective action
  3. 3.Measurement & Blueprint Reading0/5
    1. Choosing and reading micrometers and calipers
    2. Indicators, transfer gauges and go/no-go gauges
    3. Calibration and conditions that affect accuracy
    4. Reading the print: views, lines, scale and the title block
    5. Limits, tolerance, allowance and GD&T basics
  4. 4.Manufacturing Processes & Materials0/5
    1. How parts are shaped: casting, molding, forging, machining and additive
    2. Joining, heat treating and finishing
    3. Materials and their properties
    4. Volume, setup cost, takt time and the bottleneck
    5. Work orders, travelers, traceability and connected machines
  5. 5.Lean & Continuous Improvement0/5
    1. Value-added, non-value-added and necessary work
    2. The eight wastes
    3. 5S, visual management and the andon
    4. Standard work, kaizen and plan-do-check-act
    5. Pull, value stream maps, quick changeover and poka-yoke
  6. 6.Maintenance Awareness0/5
    1. Reactive, preventive and predictive maintenance, and TPM
    2. PM discipline, maintenance records and warning signs
    3. Lockout/tagout and stored energy
    4. Lubrication, bearings and shaft alignment
    5. Belts, chains, motor overloads and fluid power
Saved in this browser. Move it to another device →
← Safety

Chapter 1 · Lesson 5 of 5

Confined spaces and ergonomics

1 min read

In a permit-required confined space, such as a tank or a pit, the attendant stays outside, keeps track of the entrants, keeps unauthorized people away and summons trained rescue.

The attendant does not go in, even when an entrant collapses, unless relieved by another attendant and trained and equipped for rescue under the employer's program, because a large share of confined-space deaths are would-be rescuers overcome by the same atmosphere.

A hot work permit authorizes spark-producing work; it does not authorize entry or rescue. Shutting off ventilation is also wrong, since it can make the atmosphere worse.

Ergonomic injuries build up over time from repetition, force, awkward or static posture, vibration and contact stress acting on the same tissue. Repeating a forceful motion with bent wrists combines several of those factors, which is why it is linked to carpal tunnel syndrome, while a single heavy lift can cause an acute injury but not a cumulative one.

The best fix follows the hierarchy: change the workstation so the awkward posture disappears for everyone, rather than posting a sign or reminding people to lift with their legs. Mats and job rotation that uses different muscle groups help reduce the risk.

Example: packers lift cases from a floor pallet to a bench hundreds of times a shift. Putting the pallet on a lift table at waist height is an engineering control and the strongest answer, even though each case is light.

Check yourself

1. Which situation at a workstation is most likely to produce a cumulative trauma disorder such as carpal tunnel syndrome?

2. An entrant working inside a permit-required confined space collapses. What should the attendant stationed outside do?

Facts checked 2026-11-15 · Sources: MSSC: Certified Production Technician (CPT 4.0), OSHA 29 CFR 1910.147: The control of hazardous energy (lockout/tagout), OSHA: Hazard Communication

Production Technician cheat sheet: every key fact on one page →