Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/5
    1. Worker rights, employer duties and reporting hazards
    2. The hierarchy of controls and personal protective equipment
    3. Lockout/tagout, machine guarding and electrical hazards
    4. Hazard communication, chemical storage and fire
    5. Confined spaces and ergonomics
  2. 2.Quality Practices & Inspection0/4
    1. Quality systems, audits and the internal customer
    2. Prevention versus detection: cost of quality and inspection points
    3. Control charts and variation
    4. Root cause tools, nonconforming product and corrective action
  3. 3.Measurement & Blueprint Reading0/5
    1. Choosing and reading micrometers and calipers
    2. Indicators, transfer gauges and go/no-go gauges
    3. Calibration and conditions that affect accuracy
    4. Reading the print: views, lines, scale and the title block
    5. Limits, tolerance, allowance and GD&T basics
  4. 4.Manufacturing Processes & Materials0/5
    1. How parts are shaped: casting, molding, forging, machining and additive
    2. Joining, heat treating and finishing
    3. Materials and their properties
    4. Volume, setup cost, takt time and the bottleneck
    5. Work orders, travelers, traceability and connected machines
  5. 5.Lean & Continuous Improvement0/5
    1. Value-added, non-value-added and necessary work
    2. The eight wastes
    3. 5S, visual management and the andon
    4. Standard work, kaizen and plan-do-check-act
    5. Pull, value stream maps, quick changeover and poka-yoke
  6. 6.Maintenance Awareness0/5
    1. Reactive, preventive and predictive maintenance, and TPM
    2. PM discipline, maintenance records and warning signs
    3. Lockout/tagout and stored energy
    4. Lubrication, bearings and shaft alignment
    5. Belts, chains, motor overloads and fluid power
Saved in this browser. Move it to another device →
← Measurement & Blueprint Reading

Chapter 3 · Lesson 5 of 5

Limits, tolerance, allowance and GD&T basics

1 min read

A toleranced dimension defines two limits, and the total tolerance is the difference between them.

Example: a pin dimensioned 0.875 in plus 0.002 minus 0.001 has an upper limit of 0.877 in and a lower limit of 0.874 in, so the total tolerance is 0.003 in. A tolerance that allows variation in both directions is bilateral, even when the plus and minus values differ; a unilateral tolerance allows variation in only one direction.

In a shaft-and-hole fit, allowance is the tightest intended condition: the smallest hole minus the largest shaft.

Example: a hole of 0.500 to 0.503 in with a shaft of 0.495 to 0.498 in gives an allowance of 0.500 minus 0.498 = 0.002 in, while the loosest clearance is 0.503 minus 0.495 = 0.008 in. A negative allowance means an interference fit.

In geometric dimensioning and tolerancing, form controls such as flatness, straightness, circularity and cylindricity describe one feature by itself, so their feature control frame lists no datum. Orientation, location and runout controls relate a feature to a datum. The frame reads in order: the geometric symbol, the tolerance zone, any material modifier, then the datums.

Check yourself

1. A shaft is dimensioned 1.250 in with a tolerance of plus 0.003 in and minus 0.001 in. What are its limits and total tolerance?

2. Which geometric characteristic appears in a feature control frame with no datum reference at all?

Facts checked 2026-11-15 · Sources: MSSC: Certified Production Technician (CPT 4.0), NIST: Metrological traceability

Production Technician cheat sheet: every key fact on one page →