Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/5
    1. Worker rights, employer duties and reporting hazards
    2. The hierarchy of controls and personal protective equipment
    3. Lockout/tagout, machine guarding and electrical hazards
    4. Hazard communication, chemical storage and fire
    5. Confined spaces and ergonomics
  2. 2.Quality Practices & Inspection0/4
    1. Quality systems, audits and the internal customer
    2. Prevention versus detection: cost of quality and inspection points
    3. Control charts and variation
    4. Root cause tools, nonconforming product and corrective action
  3. 3.Measurement & Blueprint Reading0/5
    1. Choosing and reading micrometers and calipers
    2. Indicators, transfer gauges and go/no-go gauges
    3. Calibration and conditions that affect accuracy
    4. Reading the print: views, lines, scale and the title block
    5. Limits, tolerance, allowance and GD&T basics
  4. 4.Manufacturing Processes & Materials0/5
    1. How parts are shaped: casting, molding, forging, machining and additive
    2. Joining, heat treating and finishing
    3. Materials and their properties
    4. Volume, setup cost, takt time and the bottleneck
    5. Work orders, travelers, traceability and connected machines
  5. 5.Lean & Continuous Improvement0/5
    1. Value-added, non-value-added and necessary work
    2. The eight wastes
    3. 5S, visual management and the andon
    4. Standard work, kaizen and plan-do-check-act
    5. Pull, value stream maps, quick changeover and poka-yoke
  6. 6.Maintenance Awareness0/5
    1. Reactive, preventive and predictive maintenance, and TPM
    2. PM discipline, maintenance records and warning signs
    3. Lockout/tagout and stored energy
    4. Lubrication, bearings and shaft alignment
    5. Belts, chains, motor overloads and fluid power
Saved in this browser. Move it to another device →
← Maintenance Awareness

Chapter 6 · Lesson 4 of 5

Lubrication, bearings and shaft alignment

1 min read

In a rolling-element bearing, the lubricant's main job is to form a thin film that keeps the rolling surfaces apart so metal does not touch metal. The film also carries heat away and flushes out wear debris. Once it is lost through wrong viscosity, dirt or too little lubricant, the bearing heats and wears quickly.

  • Too much grease is also harmful. The rolling elements churn the excess, heat builds, the oil breaks down, and pressure can push the seals out. The quantity on the lube chart governs.
  • Grease is oil held in a thickener, so it stays put and helps seal slow, sealed or hard-to-reach points. Oil flows, so circulating systems use it to carry heat and debris away from high-speed parts.
  • Contamination and improper lubrication are leading causes of bearings failing early, well before their design fatigue life. Rising heat, changed noise and more vibration are the early warning.

Misalignment between coupled shafts is close behind. Parallel, or offset, misalignment means the centerlines stay parallel but are shifted sideways; angular misalignment means they meet at an angle, and most machines show some of both. A flexible coupling only absorbs a little, so shafts are aligned with a straightedge, dial indicator or laser.

Check yourself

1. What is the likely result of pumping far more grease into a bearing than the lube chart calls for?

2. Two coupled shaft centerlines run parallel to each other but are offset side to side. This condition is called:

Facts checked 2026-11-15 · Sources: MSSC: Certified Production Technician (CPT 4.0), OSHA 29 CFR 1910.147: The control of hazardous energy (lockout/tagout)

Production Technician cheat sheet: every key fact on one page →