Production Technician Cheat Sheet: Key Facts
Every key takeaway and common trap from the Production Technician study guide on one page, grouped by chapter. Tap a lesson link to read the full explanation.
44 facts · 6 chaptersFacts checked 2026-11-15
Chapter 1
Safety
Key takeaways
- Report hazards and near misses through the company procedure, and know that federal law forbids punishing a worker for reporting. → Worker rights, employer duties and reporting hazards
- The hierarchy of controls runs elimination, substitution, engineering, administrative, then PPE, and the higher control is the better answer. → The hierarchy of controls and personal protective equipment
- After locking and tagging a machine, release stored energy and verify zero energy before any work begins, and remove only your own lock. → Lockout/tagout, machine guarding and electrical hazards
- Every workplace chemical container needs the product identity and hazard information, and the safety data sheet must be reachable on every shift. → Hazard communication, chemical storage and fire
- A confined-space attendant stays outside and calls trained rescue, because would-be rescuers are often overcome by the same atmosphere. → Confined spaces and ergonomics
Common trap
- Wrong answers often stop the lockout one step early, for example locking and tagging and then starting the repair, or running one cycle to test the machine. The correct next step after applying locks is to release stored energy and verify zero energy. → Lockout/tagout, machine guarding and electrical hazards
- Distractors pick an extinguisher by what looks like it is burning, such as Class A for wire insulation or Class D for a metal cabinet. While the circuit is live, the deciding fact is that the agent must not conduct electricity. → Hazard communication, chemical storage and fire
Quick reference
| Control level | Example at a noisy press line |
|---|---|
| Substitution | Replace the press with a quieter forming method |
| Engineering | Enclose the press in a sound-damping cover |
| Administrative | Rotate operators to shorten time at the press |
| PPE | Issue earplugs |
Chapter 2
Quality Practices & Inspection
Key takeaways
- A quality management system is the documented procedures and records that control the work, not a department or an inspection station. → Quality systems, audits and the internal customer
- Prevention costs the least and external failure costs the most, which is why quality is built into the process instead of inspected in at the end. → Prevention versus detection: cost of quality and inspection points
- Control limits come from process data and specification limits come from the customer or drawing, so a stable process can still be incapable. → Control charts and variation
- A point beyond a control limit or a long run on one side of the center line means find what changed, never widen the limits or overadjust. → Control charts and variation
- Containment protects the customer, a correction fixes the parts already made, and a corrective action removes the root cause. → Root cause tools, nonconforming product and corrective action
Common trap
- In control is not the same as capable. A stable process whose spread is too wide or off center will keep making out-of-tolerance parts predictably, and the fix is an engineering or management change, not an operator adjusting after every bad part. → Control charts and variation
- Distractors swap correction and corrective action. Reworking the bad parts is a correction; changing the fixture that allowed the mistake is the corrective action. → Root cause tools, nonconforming product and corrective action
Quick reference
| Audit type | Who audits whom |
|---|---|
| First-party | The plant audits itself (internal audit) |
| Second-party | A customer audits its supplier |
| Third-party | An independent registrar audits for certification |
| Step | What it does |
|---|---|
| Containment | Sorts and holds suspect stock to protect the customer; changes nothing in the process |
| Correction | Fixes the parts already made, such as rework |
| Corrective action | Removes the root cause so the problem does not return |
| Preventive action | Addresses a problem that has not happened yet |
Chapter 3
Measurement & Blueprint Reading
Key takeaways
- By the rule of ten, the instrument should resolve about one tenth of the tolerance being checked. → Choosing and reading micrometers and calipers
- An inch micrometer reading is the numbered sleeve value plus each exposed 0.025 in step plus the thimble thousandths. → Choosing and reading micrometers and calipers
- Indicators compare to a zero, transfer gauges need a micrometer to read them, and go/no-go gauges only accept or reject. → Indicators, transfer gauges and go/no-go gauges
- When a gauge fails calibration, every part measured since its last good calibration is suspect and is re-inspected. → Calibration and conditions that affect accuracy
- Never scale a print; an untoleranced dimension takes the title-block default for its number of decimal places. → Reading the print: views, lines, scale and the title block
Common trap
- The most common micrometer error is dropping the 0.025 in steps between numbered sleeve marks, which turns a reading like 0.367 in into 0.317 in. Also watch for answers that add a fourth decimal place a plain micrometer cannot read. → Choosing and reading micrometers and calipers
- Answer choices often swap allowance for the total tolerance or for the maximum clearance. Allowance always uses the largest shaft and the smallest hole. → Limits, tolerance, allowance and GD&T basics
Quick reference
| Gauge | What it tells you |
|---|---|
| Dial indicator | How far a surface departs from a reference zero set on a master or gauge block |
| Telescoping or small-hole gauge | Nothing by itself; it is locked in the bore and then read with an outside micrometer |
| Go/no-go plug gauge | Accept or reject only; no actual dimension |
| Feeler gauge | The clearance in a narrow gap, from the blade that slides through with light drag |
Chapter 4
Manufacturing Processes & Materials
Key takeaways
- Casting and molding fill a cavity, forging and stamping deform solid material, machining removes chips, and additive manufacturing builds in layers. → How parts are shaped: casting, molding, forging, machining and additive
- Expensive tooling such as dies and molds only pays off when high volume spreads its fixed cost over many parts. → Volume, setup cost, takt time and the bottleneck
- Takt time is available production time divided by customer demand, and the slowest station sets the real output of a line. → Volume, setup cost, takt time and the bottleneck
- If material does not match the work order, stop and tell the supervisor before running anything. → Work orders, travelers, traceability and connected machines
- Lot numbers scanned at each step give traceability, and connected sensors help catch problems before failure, but neither replaces procedures or records. → Work orders, travelers, traceability and connected machines
Common trap
- Watch for answers from the wrong family. A distractor may offer sand casting for a plastic part, or a hardening treatment for a part that is already too hard. First decide what the stem needs (metal or plastic, softer or harder, permanent or removable), then cross out every option that goes the wrong direction. → Joining, heat treating and finishing
- In bottleneck questions the distractors are usually the sum of all station times and the average. The sum (110 seconds in the example) is roughly how long one piece takes to travel the line, and the average matches no real station. Output is set by the single slowest station. → Volume, setup cost, takt time and the bottleneck
Quick reference
| Process | What happens | Good fit |
|---|---|---|
| Sand casting | Molten metal fills a mold; cores form internal passages | Complex metal parts with hidden cavities |
| Injection molding | Molten thermoplastic is forced into a steel mold | Huge runs of identical plastic parts |
| Forging | A hammer or press moves solid metal into a die | Strong parts with grain that follows the shape |
| Machining | A tool cuts chips until the size is reached | Precise features, low volumes |
| Additive | Material is added layer by layer from a digital model | Prototypes, fixtures, shapes that cannot be cut |
Chapter 5
Lean & Continuous Improvement
Key takeaways
- Value-added work changes the product toward what the customer ordered; required safety checks are non-value-added but necessary and are never removed. → Value-added, non-value-added and necessary work
- Motion is waste by people, transportation is waste by material, and overproduction is the worst waste because it creates the others. → The eight wastes
- 5S runs Sort, Set in Order, Shine, Standardize, Sustain, and Shine doubles as inspection. → 5S, visual management and the andon
- Standard work is the baseline, and in plan-do-check-act the Check step compares results with data taken before the change. → Standard work, kaizen and plan-do-check-act
- A kanban authorizes making only the quantity just used, and poka-yoke prevents an error instead of catching it afterward. → Pull, value stream maps, quick changeover and poka-yoke
Common trap
- When a question asks what an improvement team should cut, a required safety check is never the answer. Lean removes pure waste; it does not remove guarding checks, lockout steps or other duties the employer's safety program requires. → Value-added, non-value-added and necessary work
- Waste questions often pair motion with transportation. Ask who or what is moving. If the operator walks or reaches, it is motion and the fix is point-of-use storage; if the product travels, it is transportation and the fix is moving operations closer together, not buying a faster forklift. → The eight wastes
- PDCA questions often offer writing the change into standard work or rolling it out to every shift as the Check step. Both belong to Act. Check means comparing results with the before data; standardizing a change nobody verified locks in changes that may not work. → Standard work, kaizen and plan-do-check-act
Quick reference
| Category | Example in a machining cell | Lean response |
|---|---|---|
| Value-added | Drilling a hole the print calls for | Keep it and do it right the first time |
| Non-value-added but necessary | Testing the guard interlock before a run | Keep it; required safety checks are never cut |
| Pure waste | Redrilling a hole that came out off-center | Remove it by fixing the cause |
Chapter 6
Maintenance Awareness
Key takeaways
- Reactive maintenance waits for failure, preventive works on a schedule, and predictive trends a measured condition such as vibration. → Reactive, preventive and predictive maintenance, and TPM
- A PM is complete only when it is recorded, and a PM that cannot be done on time is escalated for rescheduling, never skipped or signed in advance. → PM discipline, maintenance records and warning signs
- Under lockout, each worker's lock is removed only by that worker, and stored energy is relieved and zero energy verified before work starts. → Lockout/tagout and stored energy
- Contamination and wrong lubrication, too little or too much, are leading causes of early bearing failure. → Lubrication, bearings and shaft alignment
- A tripping overload relay is a symptom to investigate, and a hydraulic pump makes flow while pressure comes from resistance. → Belts, chains, motor overloads and fluid power
Common trap
- A fixed schedule is not predictive. Greasing on an hour-based interval or rebuilding during an annual shutdown is preventive work, even though it is planned ahead; predictive work needs a measured condition, such as vibration readings, that is trended over time. → Reactive, preventive and predictive maintenance, and TPM
- When several workers are locked out on one machine, each keeps the only key to a personal lock, and only that worker removes it. A supervisor, a lead or a co-worker who finishes first may not remove someone else's lock; the standard allows that only through the employer's documented exception procedure after the worker's absence is verified. → Lockout/tagout and stored energy
- Bypass answers are always wrong. Resetting an overload again and again, jumpering it out, or fitting a larger relay removes the protection while leaving the fault in place. The same goes for raising a regulator to push water through or pulling a filter element. → Belts, chains, motor overloads and fluid power
Quick reference
| Strategy | Trigger | Example |
|---|---|---|
| Reactive | The part has already failed | Replacing a motor after it burns out |
| Preventive | A fixed time or hour interval | Greasing a bearing on schedule; a shutdown rebuild |
| Predictive | A measured condition trending worse | Trending vibration, temperature or oil condition |