Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/5
    1. Worker rights, employer duties and reporting hazards
    2. The hierarchy of controls and personal protective equipment
    3. Lockout/tagout, machine guarding and electrical hazards
    4. Hazard communication, chemical storage and fire
    5. Confined spaces and ergonomics
  2. 2.Quality Practices & Inspection0/4
    1. Quality systems, audits and the internal customer
    2. Prevention versus detection: cost of quality and inspection points
    3. Control charts and variation
    4. Root cause tools, nonconforming product and corrective action
  3. 3.Measurement & Blueprint Reading0/5
    1. Choosing and reading micrometers and calipers
    2. Indicators, transfer gauges and go/no-go gauges
    3. Calibration and conditions that affect accuracy
    4. Reading the print: views, lines, scale and the title block
    5. Limits, tolerance, allowance and GD&T basics
  4. 4.Manufacturing Processes & Materials0/5
    1. How parts are shaped: casting, molding, forging, machining and additive
    2. Joining, heat treating and finishing
    3. Materials and their properties
    4. Volume, setup cost, takt time and the bottleneck
    5. Work orders, travelers, traceability and connected machines
  5. 5.Lean & Continuous Improvement0/5
    1. Value-added, non-value-added and necessary work
    2. The eight wastes
    3. 5S, visual management and the andon
    4. Standard work, kaizen and plan-do-check-act
    5. Pull, value stream maps, quick changeover and poka-yoke
  6. 6.Maintenance Awareness0/5
    1. Reactive, preventive and predictive maintenance, and TPM
    2. PM discipline, maintenance records and warning signs
    3. Lockout/tagout and stored energy
    4. Lubrication, bearings and shaft alignment
    5. Belts, chains, motor overloads and fluid power
Saved in this browser. Move it to another device →
← Quality Practices & Inspection

Chapter 2 · Lesson 1 of 4

Quality systems, audits and the internal customer

1 min read

A quality management system is the set of documented policies, procedures, work instructions and records that directs how work is done and proves it was done correctly.

Exam questions offer tempting physical answers, such as the inspection crew, the gauge lab or the final check station, but the system is the documentation and evidence, not a group of people or tools.

Records matter because of traceability: an inspection record that carries the lot number, date, part number and gauge used lets the plant trace a later problem back to the exact parts and equipment involved. Records are kept for the retention period the company, customer or regulator sets, not thrown away at shipment.

Audit typeWho audits whom
First-partyThe plant audits itself (internal audit)
Second-partyA customer audits its supplier
Third-partyAn independent registrar audits for certification

In any audit the auditor compares what happens on the floor with what the written procedure says and gathers objective evidence; it judges the system, not one operator's speed. The next workstation that receives your parts is your internal customer, and handing it a defect is as costly as shipping one.

Example: a customer's quality engineer visits to review how the supplier runs its process; that is a second-party audit, and it looks at the system rather than at any one operator's output.

Check yourself

1. An audit performed by an independent registrar so the plant can be certified to a recognized quality standard is a ___.

2. A completed inspection record carries the lot number, date, part number and gauge used mainly so that ___.

Facts checked 2026-11-15 · Sources: MSSC: Certified Production Technician (CPT 4.0), NIST/SEMATECH e-Handbook of Statistical Methods: Introduction to control charts

Production Technician cheat sheet: every key fact on one page →