Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/5
    1. Worker rights, employer duties and reporting hazards
    2. The hierarchy of controls and personal protective equipment
    3. Lockout/tagout, machine guarding and electrical hazards
    4. Hazard communication, chemical storage and fire
    5. Confined spaces and ergonomics
  2. 2.Quality Practices & Inspection0/4
    1. Quality systems, audits and the internal customer
    2. Prevention versus detection: cost of quality and inspection points
    3. Control charts and variation
    4. Root cause tools, nonconforming product and corrective action
  3. 3.Measurement & Blueprint Reading0/5
    1. Choosing and reading micrometers and calipers
    2. Indicators, transfer gauges and go/no-go gauges
    3. Calibration and conditions that affect accuracy
    4. Reading the print: views, lines, scale and the title block
    5. Limits, tolerance, allowance and GD&T basics
  4. 4.Manufacturing Processes & Materials0/5
    1. How parts are shaped: casting, molding, forging, machining and additive
    2. Joining, heat treating and finishing
    3. Materials and their properties
    4. Volume, setup cost, takt time and the bottleneck
    5. Work orders, travelers, traceability and connected machines
  5. 5.Lean & Continuous Improvement0/5
    1. Value-added, non-value-added and necessary work
    2. The eight wastes
    3. 5S, visual management and the andon
    4. Standard work, kaizen and plan-do-check-act
    5. Pull, value stream maps, quick changeover and poka-yoke
  6. 6.Maintenance Awareness0/5
    1. Reactive, preventive and predictive maintenance, and TPM
    2. PM discipline, maintenance records and warning signs
    3. Lockout/tagout and stored energy
    4. Lubrication, bearings and shaft alignment
    5. Belts, chains, motor overloads and fluid power
Saved in this browser. Move it to another device →
← Quality Practices & Inspection

Chapter 2 · Lesson 4 of 4

Root cause tools, nonconforming product and corrective action

1 min read

When parts fail the print, the first job is control of nonconforming product: tag them, move them to a marked hold area so they cannot be used or shipped, and let the material review authority decide the disposition, which may be use as is, rework, repair, scrap or return to supplier.

If something on the line is creating bad parts, such as coolant dripping on finished work, stop the affected work and notify the supervisor; equipment repairs belong to qualified maintenance staff.

StepWhat it does
ContainmentSorts and holds suspect stock to protect the customer; changes nothing in the process
CorrectionFixes the parts already made, such as rework
Corrective actionRemoves the root cause so the problem does not return
Preventive actionAddresses a problem that has not happened yet

To find the root cause, the five whys keeps asking why the last answer happened until a fixable cause appears. A fishbone diagram sorts possible causes under people, machine, method, material, measurement and environment, but it only organizes ideas; data proves which cause is acting.

Example: parts are scratched. Why? They rub in the tote. Why? The tote has no dividers. Why? Dividers were never on the packing instruction. Adding them to the instruction fixes the cause, not just this batch.

Check yourself

1. Reworking the bad parts and then changing the fixture that let them be loaded wrong are, in order, ___.

2. A cause-and-effect (fishbone) diagram is used to ___.

Facts checked 2026-11-15 · Sources: MSSC: Certified Production Technician (CPT 4.0), NIST/SEMATECH e-Handbook of Statistical Methods: Introduction to control charts

Production Technician cheat sheet: every key fact on one page →