Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/5
    1. Worker rights, employer duties and reporting hazards
    2. The hierarchy of controls and personal protective equipment
    3. Lockout/tagout, machine guarding and electrical hazards
    4. Hazard communication, chemical storage and fire
    5. Confined spaces and ergonomics
  2. 2.Quality Practices & Inspection0/4
    1. Quality systems, audits and the internal customer
    2. Prevention versus detection: cost of quality and inspection points
    3. Control charts and variation
    4. Root cause tools, nonconforming product and corrective action
  3. 3.Measurement & Blueprint Reading0/5
    1. Choosing and reading micrometers and calipers
    2. Indicators, transfer gauges and go/no-go gauges
    3. Calibration and conditions that affect accuracy
    4. Reading the print: views, lines, scale and the title block
    5. Limits, tolerance, allowance and GD&T basics
  4. 4.Manufacturing Processes & Materials0/5
    1. How parts are shaped: casting, molding, forging, machining and additive
    2. Joining, heat treating and finishing
    3. Materials and their properties
    4. Volume, setup cost, takt time and the bottleneck
    5. Work orders, travelers, traceability and connected machines
  5. 5.Lean & Continuous Improvement0/5
    1. Value-added, non-value-added and necessary work
    2. The eight wastes
    3. 5S, visual management and the andon
    4. Standard work, kaizen and plan-do-check-act
    5. Pull, value stream maps, quick changeover and poka-yoke
  6. 6.Maintenance Awareness0/5
    1. Reactive, preventive and predictive maintenance, and TPM
    2. PM discipline, maintenance records and warning signs
    3. Lockout/tagout and stored energy
    4. Lubrication, bearings and shaft alignment
    5. Belts, chains, motor overloads and fluid power
Saved in this browser. Move it to another device →
← Manufacturing Processes & Materials

Chapter 4 · Lesson 3 of 5

Materials and their properties

1 min read

Metals are sorted into ferrous and non-ferrous. Ferrous metals are iron based, so most are magnetic and likely to rust when moisture reaches bare metal; austenitic stainless steels are a common non-magnetic exception.

Aluminum, copper and brass are non-ferrous: they contain no iron and a magnet will not stick to them. Example: a technician sorting scrap can hold a magnet to each piece; anything that grabs it goes in the ferrous bin.

  • Ductility: stretching a long way before breaking, which is what lets copper be drawn into wire.
  • Hardness: resistance to indentation and wear.
  • Elasticity: springing back to the original shape after a load is removed.
  • Brittleness: snapping with little or no stretch.

Plastics split the same way the exam expects you to know. Thermoplastics are not cross-linked, so they soften every time they are heated; trimmed scrap can be ground into regrind and molded again within limits.

Thermosets, vulcanized rubber and fired ceramics are permanently cross-linked or fused, so heat makes them char, tear or crack instead of melt. If a stem mentions remelting scrap, think thermoplastic.

Property questions are usually worded as a job to be done: drawing wire, bending a bracket, or resisting wear. Match the job to the property it demands, and watch for elasticity as a distractor, because springing back is the opposite of the permanent stretch that forming needs.

Check yourself

1. A magnet sticks firmly to a scrap piece in the metal bin. What does that tell the technician about the material?

2. Trimmed scrap from a molding press is ground up, melted and molded again. Which material family behaves this way?

Facts checked 2026-11-15 · Sources: MSSC: Certified Production Technician (CPT 4.0)

Production Technician cheat sheet: every key fact on one page →