Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/4
    1. Lockout, tagout and stored electrical energy
    2. Refrigerant, cylinders and pressure hazards
    3. Carbon monoxide and combustion hazards
    4. PPE, brazing and job-site hazards
  2. 2.Tools & Measurement0/5
    1. Measuring temperature and proving the thermometer
    2. Humidity, wet bulb and dew point
    3. Gauge pressure, absolute pressure and vacuum
    4. Using electrical meters correctly
    5. Airflow, leak detection and charging tools
  3. 3.Basic Electrical0/4
    1. Ohm's law, power and power factor
    2. Series, parallel and reading a ladder diagram
    3. Transformers, single-phase and three-phase power
    4. Single-phase motors, capacitors and winding tests
  4. 4.Science & Refrigeration Cycle0/4
    1. Heat, sensible and latent heat, and heat transfer
    2. Saturation and the four main components
    3. Calculating superheat and subcooling
    4. Metering devices and reading the charge
  5. 5.Construction, Comfort & Airflow0/4
    1. The building envelope: insulation, air sealing and windows
    2. Loads, equipment sizing and comfort
    3. Airflow, static pressure and capacity
    4. Duct leakage, noise, filters and ventilation
  6. 6.AC Components & Operation0/4
    1. Compressors and keeping liquid out
    2. Outdoor coil, indoor coil and condensate
    3. Metering devices, the TXV bulb and charging method
    4. Line sets, accessories, service valves and thermostats
  7. 7.AC Diagnosis & Service0/4
    1. Reading superheat and subcooling patterns
    2. Troubleshooting the control circuit
    3. Compressor electrical faults
    4. Airside, static pressure and condensate problems
Saved in this browser. Move it to another device →
← Safety

Chapter 1 · Lesson 2 of 4

Refrigerant, cylinders and pressure hazards

1 min read

Liquid refrigerant boils at a very low temperature at atmospheric pressure. When it escapes from a hose it flashes to vapor and pulls heat from whatever it touches, which is why it causes frostbite on skin and can freeze eye tissue.

That is the reason for gloves and eye protection when connecting and disconnecting hoses. Clean refrigerant is not an acid, though it becomes corrosive after it decomposes in a flame.

SituationHazardSafe practice
Charging cylinder transfers slowlyFlame spikes pressure and softens steelGentle warming such as a warm-water bath, within the marked limit
Filling a recovery cylinderLiquid expands with heat and has no roomFill by weight on a scale and keep a vapor space
Large leak in a basementVapor is heavier than air and displaces oxygenVentilate and test the air before entering

A pressure relief device is a last-resort safeguard that releases refrigerant so an overheated or overfilled vessel does not rupture. It is never plugged, capped or adjusted, and if it has opened, the technician finds the cause.

Example: a recovery cylinder left in a hot truck with no vapor space can build pressure fast because liquid barely compresses, so a small temperature rise causes a large pressure rise. After a large leak in a low space, the danger is asphyxiation, not smell, so never enter on the assumption that you will notice trouble in time.

Check yourself

1. Recovery cylinders are filled by weight to a stated maximum and are never filled completely. What is the reason?

2. Why are gloves and eye protection worn when connecting and disconnecting refrigerant hoses?

Facts checked 2026-11-15 · Sources: NATE: Certification exams, OSHA 29 CFR 1910.147: The control of hazardous energy (lockout/tagout)

NATE HVAC cheat sheet: every key fact on one page →