Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/4
    1. Lockout, tagout and stored electrical energy
    2. Refrigerant, cylinders and pressure hazards
    3. Carbon monoxide and combustion hazards
    4. PPE, brazing and job-site hazards
  2. 2.Tools & Measurement0/5
    1. Measuring temperature and proving the thermometer
    2. Humidity, wet bulb and dew point
    3. Gauge pressure, absolute pressure and vacuum
    4. Using electrical meters correctly
    5. Airflow, leak detection and charging tools
  3. 3.Basic Electrical0/4
    1. Ohm's law, power and power factor
    2. Series, parallel and reading a ladder diagram
    3. Transformers, single-phase and three-phase power
    4. Single-phase motors, capacitors and winding tests
  4. 4.Science & Refrigeration Cycle0/4
    1. Heat, sensible and latent heat, and heat transfer
    2. Saturation and the four main components
    3. Calculating superheat and subcooling
    4. Metering devices and reading the charge
  5. 5.Construction, Comfort & Airflow0/4
    1. The building envelope: insulation, air sealing and windows
    2. Loads, equipment sizing and comfort
    3. Airflow, static pressure and capacity
    4. Duct leakage, noise, filters and ventilation
  6. 6.AC Components & Operation0/4
    1. Compressors and keeping liquid out
    2. Outdoor coil, indoor coil and condensate
    3. Metering devices, the TXV bulb and charging method
    4. Line sets, accessories, service valves and thermostats
  7. 7.AC Diagnosis & Service0/4
    1. Reading superheat and subcooling patterns
    2. Troubleshooting the control circuit
    3. Compressor electrical faults
    4. Airside, static pressure and condensate problems
Saved in this browser. Move it to another device →
← Back

Study guide · Chapter 4 of 7

Science & Refrigeration Cycle Study Guide — NATE HVAC

26 free practice questions

The refrigeration cycle is the backbone of the NATE Core exam and of every service call that follows it. Questions test how heat moves, why pressure and temperature are locked together at saturation, and how to turn a pressure and a line temperature into superheat or subcooling. If you can explain what the refrigerant is doing at each point in the loop, most of these questions answer themselves.

Key takeaways

  • An air conditioner moves heat from indoors to outdoors; there is no such thing as cold energy.
  • At saturation each pressure matches one temperature, which is what a pressure-temperature chart lists.
  • Superheat is line temperature minus saturation temperature; subcooling is saturation temperature minus line temperature.
  • Fixed-orifice systems are charged by superheat and TXV systems by subcooling.
  • High superheat with low subcooling points to an undercharge; high superheat with normal or high subcooling points to a restriction.

Lessons in this chapter

4 short lessons · 4 min read

  1. 1Heat, sensible and latent heat, and heat transfer1 min
  2. 2Saturation and the four main components1 min
  3. 3Calculating superheat and subcooling1 min
  4. 4Metering devices and reading the charge1 min
View all questions & answers →

Facts checked 2026-11-15 · Sources: NATE: Certification exams

NATE HVAC cheat sheet: every key fact on one page →Next chapter: Construction, Comfort & Airflow →

Practice questions based on the published NATE knowledge areas and standard HVACR theory and service practice. NATE is a mark of North American Technician Excellence; this site is not affiliated with or endorsed by NATE. NATE certification is not a licence — HVAC licensing is set by your state and locality. Confirm current exam requirements with NATE and current code requirements with the authority having jurisdiction. About NATE certification →