Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/4
    1. Lockout, tagout and stored electrical energy
    2. Refrigerant, cylinders and pressure hazards
    3. Carbon monoxide and combustion hazards
    4. PPE, brazing and job-site hazards
  2. 2.Tools & Measurement0/5
    1. Measuring temperature and proving the thermometer
    2. Humidity, wet bulb and dew point
    3. Gauge pressure, absolute pressure and vacuum
    4. Using electrical meters correctly
    5. Airflow, leak detection and charging tools
  3. 3.Basic Electrical0/4
    1. Ohm's law, power and power factor
    2. Series, parallel and reading a ladder diagram
    3. Transformers, single-phase and three-phase power
    4. Single-phase motors, capacitors and winding tests
  4. 4.Science & Refrigeration Cycle0/4
    1. Heat, sensible and latent heat, and heat transfer
    2. Saturation and the four main components
    3. Calculating superheat and subcooling
    4. Metering devices and reading the charge
  5. 5.Construction, Comfort & Airflow0/4
    1. The building envelope: insulation, air sealing and windows
    2. Loads, equipment sizing and comfort
    3. Airflow, static pressure and capacity
    4. Duct leakage, noise, filters and ventilation
  6. 6.AC Components & Operation0/4
    1. Compressors and keeping liquid out
    2. Outdoor coil, indoor coil and condensate
    3. Metering devices, the TXV bulb and charging method
    4. Line sets, accessories, service valves and thermostats
  7. 7.AC Diagnosis & Service0/4
    1. Reading superheat and subcooling patterns
    2. Troubleshooting the control circuit
    3. Compressor electrical faults
    4. Airside, static pressure and condensate problems
Saved in this browser. Move it to another device →
← Construction, Comfort & Airflow

Chapter 5 · Lesson 3 of 4

Airflow, static pressure and capacity

1 min read

In a duct, total pressure equals static pressure plus velocity pressure. Static pressure pushes outward on the duct walls in every direction. Velocity pressure exists only because the air is moving and is sensed facing into the stream.

A blower delivers less air as the resistance against it rises, which is what a fan curve shows. A loaded filter, an undersized return or furniture over the only return grille all raise static pressure and cut airflow.

  • Less air across a cooling coil makes the coil colder, cuts capacity, and in severe cases freezes the coil.
  • Raising blower speed warms the coil and shifts capacity toward sensible cooling, which makes humidity control worse, not better.

Airflow can be estimated from temperature rise with CFM = BTU/h ÷ (1.08 × ΔT), where ΔT is the supply temperature minus the return temperature.

Example: a furnace delivering 54,000 BTU/h of heat with a 50°F rise is moving 54,000 ÷ (1.08 × 50) = 1,000 CFM. If the rise climbs with the same heat output, airflow has dropped, so look for a dirty filter, a closed return or a restriction.

Check yourself

1. On a system with a fixed-speed blower, a technician finds a heavily loaded filter and an undersized return, and measures an unusually high external static pressure. What is happening to airflow and to capacity?

2. A homeowner has pushed a sofa against the only return grille and keeps the bedroom doors closed against undercut-free thresholds. What happens to the cooling system?

Facts checked 2026-11-15 · Sources: NATE: Certification exams, ACCA Manual J: Residential Load Calculation

NATE HVAC cheat sheet: every key fact on one page →