Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/4
    1. Lockout, tagout and stored electrical energy
    2. Refrigerant, cylinders and pressure hazards
    3. Carbon monoxide and combustion hazards
    4. PPE, brazing and job-site hazards
  2. 2.Tools & Measurement0/5
    1. Measuring temperature and proving the thermometer
    2. Humidity, wet bulb and dew point
    3. Gauge pressure, absolute pressure and vacuum
    4. Using electrical meters correctly
    5. Airflow, leak detection and charging tools
  3. 3.Basic Electrical0/4
    1. Ohm's law, power and power factor
    2. Series, parallel and reading a ladder diagram
    3. Transformers, single-phase and three-phase power
    4. Single-phase motors, capacitors and winding tests
  4. 4.Science & Refrigeration Cycle0/4
    1. Heat, sensible and latent heat, and heat transfer
    2. Saturation and the four main components
    3. Calculating superheat and subcooling
    4. Metering devices and reading the charge
  5. 5.Construction, Comfort & Airflow0/4
    1. The building envelope: insulation, air sealing and windows
    2. Loads, equipment sizing and comfort
    3. Airflow, static pressure and capacity
    4. Duct leakage, noise, filters and ventilation
  6. 6.AC Components & Operation0/4
    1. Compressors and keeping liquid out
    2. Outdoor coil, indoor coil and condensate
    3. Metering devices, the TXV bulb and charging method
    4. Line sets, accessories, service valves and thermostats
  7. 7.AC Diagnosis & Service0/4
    1. Reading superheat and subcooling patterns
    2. Troubleshooting the control circuit
    3. Compressor electrical faults
    4. Airside, static pressure and condensate problems
Saved in this browser. Move it to another device →
← Back

Study guide · Chapter 6 of 7

AC Components & Operation Study Guide — NATE HVAC

28 free practice questions

The NATE Air Conditioning Service specialty expects you to know what each part of a cooling system does when it is working right, because you cannot spot a fault without a picture of normal. This chapter walks the loop: the compressor and the parts that protect it, the outdoor and indoor coils, the metering device, and the line set, accessories and controls. For each part, learn its job and what happens to pressures and temperatures when it cannot do that job.

Key takeaways

  • Compressors pump vapor; liquid reaching them breaks parts and washes away oil, so crankcase heaters and accumulators keep it out.
  • Warmer outdoor air or a dirty condenser raises condensing temperature and head pressure.
  • Low airflow across the indoor coil drops coil temperature until the coil can freeze.
  • A TXV bulb goes tight on top of a small horizontal suction line, or at 4 or 8 o'clock on lines 7/8 inch and larger, and is insulated.
  • Service valves run back seated; front seating isolates the compressor.

Lessons in this chapter

4 short lessons · 4 min read

  1. 1Compressors and keeping liquid out1 min
  2. 2Outdoor coil, indoor coil and condensate1 min
  3. 3Metering devices, the TXV bulb and charging method1 min
  4. 4Line sets, accessories, service valves and thermostats1 min
View all questions & answers →

Facts checked 2026-11-15 · Sources: NATE: Certification exams

NATE HVAC cheat sheet: every key fact on one page →Next chapter: AC Diagnosis & Service →

Practice questions based on the published NATE knowledge areas and standard HVACR theory and service practice. NATE is a mark of North American Technician Excellence; this site is not affiliated with or endorsed by NATE. NATE certification is not a licence — HVAC licensing is set by your state and locality. Confirm current exam requirements with NATE and current code requirements with the authority having jurisdiction. About NATE certification →