Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/4
    1. Lockout, tagout and stored electrical energy
    2. Refrigerant, cylinders and pressure hazards
    3. Carbon monoxide and combustion hazards
    4. PPE, brazing and job-site hazards
  2. 2.Tools & Measurement0/5
    1. Measuring temperature and proving the thermometer
    2. Humidity, wet bulb and dew point
    3. Gauge pressure, absolute pressure and vacuum
    4. Using electrical meters correctly
    5. Airflow, leak detection and charging tools
  3. 3.Basic Electrical0/4
    1. Ohm's law, power and power factor
    2. Series, parallel and reading a ladder diagram
    3. Transformers, single-phase and three-phase power
    4. Single-phase motors, capacitors and winding tests
  4. 4.Science & Refrigeration Cycle0/4
    1. Heat, sensible and latent heat, and heat transfer
    2. Saturation and the four main components
    3. Calculating superheat and subcooling
    4. Metering devices and reading the charge
  5. 5.Construction, Comfort & Airflow0/4
    1. The building envelope: insulation, air sealing and windows
    2. Loads, equipment sizing and comfort
    3. Airflow, static pressure and capacity
    4. Duct leakage, noise, filters and ventilation
  6. 6.AC Components & Operation0/4
    1. Compressors and keeping liquid out
    2. Outdoor coil, indoor coil and condensate
    3. Metering devices, the TXV bulb and charging method
    4. Line sets, accessories, service valves and thermostats
  7. 7.AC Diagnosis & Service0/4
    1. Reading superheat and subcooling patterns
    2. Troubleshooting the control circuit
    3. Compressor electrical faults
    4. Airside, static pressure and condensate problems
Saved in this browser. Move it to another device →
← Back

Study guide · Chapter 3 of 7

Basic Electrical Study Guide — NATE HVAC

29 free practice questions

Most HVAC no-cooling and no-heat calls end up as electrical problems, so the NATE Core exam tests whether you can reason through a circuit instead of guessing at parts. Expect short calculations with Ohm's law and the power formula, questions on how series and parallel circuits behave, and motor and capacitor diagnosis. Every reading in a stem is there for a reason, so use all of them.

Key takeaways

  • Ohm's law is E = I × R and the power formula is P = E × I; rearrange them to find the missing value.
  • Full source voltage across a switch that should be closed means that switch is open.
  • Loads are wired in parallel across the supply, while switches and safeties are wired in series with their own load.
  • Swapping any two line leads reverses a three-phase motor.
  • On a compressor, the highest winding reading is start to run, and the terminal left out of it is common.

Lessons in this chapter

4 short lessons · 4 min read

  1. 1Ohm's law, power and power factor1 min
  2. 2Series, parallel and reading a ladder diagram1 min
  3. 3Transformers, single-phase and three-phase power1 min
  4. 4Single-phase motors, capacitors and winding tests1 min
View all questions & answers →

Facts checked 2026-11-15 · Sources: NATE: Certification exams

NATE HVAC cheat sheet: every key fact on one page →Next chapter: Science & Refrigeration Cycle →

Practice questions based on the published NATE knowledge areas and standard HVACR theory and service practice. NATE is a mark of North American Technician Excellence; this site is not affiliated with or endorsed by NATE. NATE certification is not a licence — HVAC licensing is set by your state and locality. Confirm current exam requirements with NATE and current code requirements with the authority having jurisdiction. About NATE certification →