Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/4
    1. Lockout, tagout and stored electrical energy
    2. Refrigerant, cylinders and pressure hazards
    3. Carbon monoxide and combustion hazards
    4. PPE, brazing and job-site hazards
  2. 2.Tools & Measurement0/5
    1. Measuring temperature and proving the thermometer
    2. Humidity, wet bulb and dew point
    3. Gauge pressure, absolute pressure and vacuum
    4. Using electrical meters correctly
    5. Airflow, leak detection and charging tools
  3. 3.Basic Electrical0/4
    1. Ohm's law, power and power factor
    2. Series, parallel and reading a ladder diagram
    3. Transformers, single-phase and three-phase power
    4. Single-phase motors, capacitors and winding tests
  4. 4.Science & Refrigeration Cycle0/4
    1. Heat, sensible and latent heat, and heat transfer
    2. Saturation and the four main components
    3. Calculating superheat and subcooling
    4. Metering devices and reading the charge
  5. 5.Construction, Comfort & Airflow0/4
    1. The building envelope: insulation, air sealing and windows
    2. Loads, equipment sizing and comfort
    3. Airflow, static pressure and capacity
    4. Duct leakage, noise, filters and ventilation
  6. 6.AC Components & Operation0/4
    1. Compressors and keeping liquid out
    2. Outdoor coil, indoor coil and condensate
    3. Metering devices, the TXV bulb and charging method
    4. Line sets, accessories, service valves and thermostats
  7. 7.AC Diagnosis & Service0/4
    1. Reading superheat and subcooling patterns
    2. Troubleshooting the control circuit
    3. Compressor electrical faults
    4. Airside, static pressure and condensate problems
Saved in this browser. Move it to another device →
← Back

Study guide · Chapter 1 of 7

Safety Study Guide — NATE HVAC

20 free practice questions

The NATE Core exam is a national test of 50 questions in 1.5 hours, closed book, with a 70 percent passing score, and safety runs through all of it. Safety questions describe a job in progress and ask what the technician must do before going further. The answers rest on OSHA work rules and on the physics of stored energy, pressure and combustion, so learn the reason behind each rule.

Key takeaways

  • A locked disconnect is not proof of a dead circuit; test with a meter proved on a live source before and after.
  • Every worker on the equipment applies and removes only his or her own lock.
  • Never heat a refrigerant cylinder with a flame and never fill a recovery cylinder past its weight limit.
  • Suspected carbon monoxide exposure means people out and the appliance off before any diagnosis.
  • A face shield goes over safety glasses, never in place of them.

Lessons in this chapter

4 short lessons · 4 min read

  1. 1Lockout, tagout and stored electrical energy1 min
  2. 2Refrigerant, cylinders and pressure hazards1 min
  3. 3Carbon monoxide and combustion hazards1 min
  4. 4PPE, brazing and job-site hazards1 min
View all questions & answers →

Facts checked 2026-11-15 · Sources: NATE: Certification exams, OSHA 29 CFR 1910.147: The control of hazardous energy (lockout/tagout)

NATE HVAC cheat sheet: every key fact on one page →Next chapter: Tools & Measurement →

Practice questions based on the published NATE knowledge areas and standard HVACR theory and service practice. NATE is a mark of North American Technician Excellence; this site is not affiliated with or endorsed by NATE. NATE certification is not a licence — HVAC licensing is set by your state and locality. Confirm current exam requirements with NATE and current code requirements with the authority having jurisdiction. About NATE certification →