Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/4
    1. Lockout, tagout and stored electrical energy
    2. Refrigerant, cylinders and pressure hazards
    3. Carbon monoxide and combustion hazards
    4. PPE, brazing and job-site hazards
  2. 2.Tools & Measurement0/5
    1. Measuring temperature and proving the thermometer
    2. Humidity, wet bulb and dew point
    3. Gauge pressure, absolute pressure and vacuum
    4. Using electrical meters correctly
    5. Airflow, leak detection and charging tools
  3. 3.Basic Electrical0/4
    1. Ohm's law, power and power factor
    2. Series, parallel and reading a ladder diagram
    3. Transformers, single-phase and three-phase power
    4. Single-phase motors, capacitors and winding tests
  4. 4.Science & Refrigeration Cycle0/4
    1. Heat, sensible and latent heat, and heat transfer
    2. Saturation and the four main components
    3. Calculating superheat and subcooling
    4. Metering devices and reading the charge
  5. 5.Construction, Comfort & Airflow0/4
    1. The building envelope: insulation, air sealing and windows
    2. Loads, equipment sizing and comfort
    3. Airflow, static pressure and capacity
    4. Duct leakage, noise, filters and ventilation
  6. 6.AC Components & Operation0/4
    1. Compressors and keeping liquid out
    2. Outdoor coil, indoor coil and condensate
    3. Metering devices, the TXV bulb and charging method
    4. Line sets, accessories, service valves and thermostats
  7. 7.AC Diagnosis & Service0/4
    1. Reading superheat and subcooling patterns
    2. Troubleshooting the control circuit
    3. Compressor electrical faults
    4. Airside, static pressure and condensate problems
Saved in this browser. Move it to another device →
← Science & Refrigeration Cycle

Chapter 4 · Lesson 1 of 4

Heat, sensible and latent heat, and heat transfer

1 min read

Energy is never created or destroyed, and heat always flows from a warmer place to a cooler one. An air conditioner keeps the refrigerant in the indoor coil colder than the room air, so heat flows into the refrigerant, and that heat is later released outdoors.

The equipment does not make cold; it moves heat. Answer choices that talk about creating cold or destroying heat in the compressor are wrong.

TermMeaningHVAC example
Sensible heatChanges temperature, no change of stateLowering room dry-bulb temperature
Latent heatChanges state, no temperature changeCondensing water vapor on the coil
ConductionHeat moves by direct contactA clamp-on probe on copper
ConvectionA moving fluid carries heatAir blown across a coil
RadiationEnergy travels as waves, no medium neededAn infrared thermometer reading a surface

Both kinds of heat are measured in BTU.

On a humid day, much of the load is latent: the coil must remove heat to condense water out of the air, and that is real load even though the thermometer does not show it. Example: a house can reach the thermostat setpoint and still feel clammy because the latent part of the load was not handled.

Heat transfer questions often hide in tool questions. An infrared thermometer depends on radiation, so it reads only the surface it sees and is affected by how shiny that surface is. A coil depends on convection, so less air across it means less heat moved. Insulation on a suction line slows conduction from the surrounding air.

Check yourself

1. Which statement correctly distinguishes sensible heat from latent heat?

2. A technician points an infrared thermometer at a suction line and reads its surface temperature without touching it. Which mode of heat transfer does that instrument depend on?

Facts checked 2026-11-15 · Sources: NATE: Certification exams

NATE HVAC cheat sheet: every key fact on one page →