Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/4
    1. Lockout, tagout and stored electrical energy
    2. Refrigerant, cylinders and pressure hazards
    3. Carbon monoxide and combustion hazards
    4. PPE, brazing and job-site hazards
  2. 2.Tools & Measurement0/5
    1. Measuring temperature and proving the thermometer
    2. Humidity, wet bulb and dew point
    3. Gauge pressure, absolute pressure and vacuum
    4. Using electrical meters correctly
    5. Airflow, leak detection and charging tools
  3. 3.Basic Electrical0/4
    1. Ohm's law, power and power factor
    2. Series, parallel and reading a ladder diagram
    3. Transformers, single-phase and three-phase power
    4. Single-phase motors, capacitors and winding tests
  4. 4.Science & Refrigeration Cycle0/4
    1. Heat, sensible and latent heat, and heat transfer
    2. Saturation and the four main components
    3. Calculating superheat and subcooling
    4. Metering devices and reading the charge
  5. 5.Construction, Comfort & Airflow0/4
    1. The building envelope: insulation, air sealing and windows
    2. Loads, equipment sizing and comfort
    3. Airflow, static pressure and capacity
    4. Duct leakage, noise, filters and ventilation
  6. 6.AC Components & Operation0/4
    1. Compressors and keeping liquid out
    2. Outdoor coil, indoor coil and condensate
    3. Metering devices, the TXV bulb and charging method
    4. Line sets, accessories, service valves and thermostats
  7. 7.AC Diagnosis & Service0/4
    1. Reading superheat and subcooling patterns
    2. Troubleshooting the control circuit
    3. Compressor electrical faults
    4. Airside, static pressure and condensate problems
Saved in this browser. Move it to another device →
← Basic Electrical

Chapter 3 · Lesson 4 of 4

Single-phase motors, capacitors and winding tests

1 min read

A permanent split capacitor motor keeps its run capacitor in series with the start winding to create the phase shift that makes a rotating field. If that capacitor fails open, the motor hums, cannot start and draws locked-rotor current until the overload trips.

Locked-rotor current is high because a stopped rotor makes no counter-EMF, leaving only the low winding resistance to limit current. A start capacitor gives a short torque boost on start, and on a hermetic compressor a potential relay senses rising back-EMF from the start winding and drops the start capacitor out of the circuit.

To identify compressor terminals, take all three readings with power off and the leads removed. Example: 3 ohms, 6 ohms and 9 ohms. The largest, 9, is start to run, and it equals the other two added together, which confirms the readings.

The terminal not involved in the 9-ohm reading is common. From common, the 3-ohm path is run and the 6-ohm path is start, because the start winding has more turns of thinner wire.

  • Near zero ohms from a terminal to the housing means a grounded winding; a healthy motor reads megohms to the frame.
  • An open is a break in a winding, a short is an unwanted path between turns or windings, and a ground is a path to the frame.
  • A constant-airflow ECM speeds up and draws more watts as static pressure rises, so rising watts point to the duct system, not a bad motor.

Check yourself

1. With power off, the capacitor discharged and all leads removed, a technician measures across the three terminals of a hermetic compressor: terminals 1 to 2 read 2 ohms, terminals 1 to 3 read 5 ohms, and terminals 2 to 3 read 7 ohms. Which terminal is Start?

2. A compressor trips the breaker instantly on every start attempt. With the disconnect open, the capacitor discharged and the compressor leads removed, the technician reads near zero ohms from one motor terminal to the compressor housing. What does this indicate?

Facts checked 2026-11-15 · Sources: NATE: Certification exams

NATE HVAC cheat sheet: every key fact on one page →