Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/4
    1. Lockout, tagout and stored electrical energy
    2. Refrigerant, cylinders and pressure hazards
    3. Carbon monoxide and combustion hazards
    4. PPE, brazing and job-site hazards
  2. 2.Tools & Measurement0/5
    1. Measuring temperature and proving the thermometer
    2. Humidity, wet bulb and dew point
    3. Gauge pressure, absolute pressure and vacuum
    4. Using electrical meters correctly
    5. Airflow, leak detection and charging tools
  3. 3.Basic Electrical0/4
    1. Ohm's law, power and power factor
    2. Series, parallel and reading a ladder diagram
    3. Transformers, single-phase and three-phase power
    4. Single-phase motors, capacitors and winding tests
  4. 4.Science & Refrigeration Cycle0/4
    1. Heat, sensible and latent heat, and heat transfer
    2. Saturation and the four main components
    3. Calculating superheat and subcooling
    4. Metering devices and reading the charge
  5. 5.Construction, Comfort & Airflow0/4
    1. The building envelope: insulation, air sealing and windows
    2. Loads, equipment sizing and comfort
    3. Airflow, static pressure and capacity
    4. Duct leakage, noise, filters and ventilation
  6. 6.AC Components & Operation0/4
    1. Compressors and keeping liquid out
    2. Outdoor coil, indoor coil and condensate
    3. Metering devices, the TXV bulb and charging method
    4. Line sets, accessories, service valves and thermostats
  7. 7.AC Diagnosis & Service0/4
    1. Reading superheat and subcooling patterns
    2. Troubleshooting the control circuit
    3. Compressor electrical faults
    4. Airside, static pressure and condensate problems
Saved in this browser. Move it to another device →
← Basic Electrical

Chapter 3 · Lesson 2 of 4

Series, parallel and reading a ladder diagram

1 min read

In a series circuit the same current flows through every device, so one open device stops the whole string. That is why safety controls such as limits, rollout switches and pressure switches are wired in series with the load they protect, and why an open safety often shows up as a dead unit with no fault message.

In a parallel circuit every branch sees the same voltage and the branch currents add. If one of two parallel fan motors opens, the other keeps running at full voltage and only the total current drops.

  • On a ladder diagram, the two side rails are the power source, L1 and L2 or the hot and common of the control transformer.
  • Each rung is one circuit with one load at the right, and the switches that control it in series to its left.
  • A relay or contactor links two circuits: a small control circuit energizes the coil, and its contacts switch the larger load circuit.
  • An electric heat sequencer uses a small heater and a bimetal to close its contacts after a delay, bringing elements on in stages.

Example: with a call for cooling and 24 volts available, you read 0 volts across the thermostat contacts and 24 volts across a pressure switch. A closed contact drops almost no voltage, so the pressure switch is the open device.

Check yourself

1. With the thermostat calling and the equipment powered, a technician places the meter leads across the two terminals of a pressure switch that the schematic shows should be closed at this point in the sequence, and reads the full control voltage. What does this indicate?

2. In a furnace control circuit the thermostat contacts, a rollout switch, a high limit and the gas valve are all wired in series on one rung. The rollout switch has opened. The unit does nothing at all and no fault is indicated. Which statement best explains the symptom and the next step?

Facts checked 2026-11-15 · Sources: NATE: Certification exams

NATE HVAC cheat sheet: every key fact on one page →