Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Safety0/4
    1. Lockout, tagout and stored electrical energy
    2. Refrigerant, cylinders and pressure hazards
    3. Carbon monoxide and combustion hazards
    4. PPE, brazing and job-site hazards
  2. 2.Tools & Measurement0/5
    1. Measuring temperature and proving the thermometer
    2. Humidity, wet bulb and dew point
    3. Gauge pressure, absolute pressure and vacuum
    4. Using electrical meters correctly
    5. Airflow, leak detection and charging tools
  3. 3.Basic Electrical0/4
    1. Ohm's law, power and power factor
    2. Series, parallel and reading a ladder diagram
    3. Transformers, single-phase and three-phase power
    4. Single-phase motors, capacitors and winding tests
  4. 4.Science & Refrigeration Cycle0/4
    1. Heat, sensible and latent heat, and heat transfer
    2. Saturation and the four main components
    3. Calculating superheat and subcooling
    4. Metering devices and reading the charge
  5. 5.Construction, Comfort & Airflow0/4
    1. The building envelope: insulation, air sealing and windows
    2. Loads, equipment sizing and comfort
    3. Airflow, static pressure and capacity
    4. Duct leakage, noise, filters and ventilation
  6. 6.AC Components & Operation0/4
    1. Compressors and keeping liquid out
    2. Outdoor coil, indoor coil and condensate
    3. Metering devices, the TXV bulb and charging method
    4. Line sets, accessories, service valves and thermostats
  7. 7.AC Diagnosis & Service0/4
    1. Reading superheat and subcooling patterns
    2. Troubleshooting the control circuit
    3. Compressor electrical faults
    4. Airside, static pressure and condensate problems
Saved in this browser. Move it to another device →
← Back

Study guide · Chapter 7 of 7

AC Diagnosis & Service Study Guide — NATE HVAC

20 free practice questions

Troubleshooting questions give you a set of readings and ask for the most likely cause or the right next step. The skill being tested is reading the pattern, not reacting to one number: superheat and subcooling together, voltage across each device in a control string, or static pressure split between supply and return. Safety rules still apply, so a tripped safety control is a clue to follow, never a part to bypass.

Key takeaways

  • Read superheat and subcooling together; each fault has its own combination.
  • Non-condensables make both head pressure and subcooling read high, which looks like an overcharge.
  • In a control string, the device with full source voltage across it is the open one.
  • Prove the cheap part before condemning the expensive one, such as the run capacitor before the compressor.
  • Find where high static pressure is by measuring the drop across each component.

Lessons in this chapter

4 short lessons · 4 min read

  1. 1Reading superheat and subcooling patterns1 min
  2. 2Troubleshooting the control circuit1 min
  3. 3Compressor electrical faults1 min
  4. 4Airside, static pressure and condensate problems1 min
View all questions & answers →

Facts checked 2026-11-15 · Sources: NATE: Certification exams

NATE HVAC cheat sheet: every key fact on one page →

Practice questions based on the published NATE knowledge areas and standard HVACR theory and service practice. NATE is a mark of North American Technician Excellence; this site is not affiliated with or endorsed by NATE. NATE certification is not a licence — HVAC licensing is set by your state and locality. Confirm current exam requirements with NATE and current code requirements with the authority having jurisdiction. About NATE certification →