Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Instruments & Verification

Chapter 5 · Lesson 3 of 5

Verifying prism and centration

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

In the lensmeter, prism shows up as the target sitting off the center of the reticle. Each ring is one prism diopter, and the direction of the shift gives the base.

The lens must be held where it will sit in front of the eye. Sliding it until the target centers simply moves the optical center onto the instrument axis and hides the prism you were asked to check.

If the prism is larger than the reticle shows, hold an auxiliary prism at the stop with its base opposite to the lens prism. The target moves back into view, and the lens prism equals the auxiliary prism plus whatever displacement still remains in the original direction.

Unwanted prism from misplaced optical centers follows Prentice's rule. Example: a wearer with a 60 mm PD gets +3.00 D lenses whose optical centers are 64 mm apart.

Each center is 2 mm outward from its pupil, so each eye gets 3.00 × 0.2 = 0.60 prism diopters, 1.20 in total. In a plus lens the base points toward the optical center, which is outward here, so the effect is base out.

Check yourself

1. A lens carries so much base-in prism that the lensmeter target falls beyond the edge of the reticle. The verifier holds a 5 prism dioptre base-out auxiliary prism at the stop, and the target then rests two rings toward the nose. What prism does the lens carry?

2. A lens is ordered with 2 prism dioptres base out. At the lensmeter the target sits off to one side of the reticle centre, and a trainee slides the lens across the stop until the target is centred, then records no prism. What is the error?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), 20/20 Magazine: Honing spectacle lens verification expertise (ANSI Z80.1 sphere tolerances, compensated powers), The Vision Council: Lens Marking Guidelines (34 mm engravings, prism reference point), 20/20 Magazine: Diopter 1.53, the lens measure convention

Optician (ABO) cheat sheet: every key fact on one page →