Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Lens Products & Materials

Chapter 2 · Lesson 4 of 5

Progressive lenses

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

A progressive has no visible line, so its fitting cross must sit in front of each pupil center individually. That takes two measurements: monocular distance PDs, which allow for an uneven face, and a fitting height from the pupil center down to the lowest point of the finished lens.

Both are taken after the chosen frame is adjusted, because tilt and vertex change where the pupil falls in the opening.

Every design lists a minimum fitting height. If the frame's B measurement leaves less depth below the fitting cross than that, the near zone is cut off during edging.

Example: a design that needs 16 mm, in a shallow frame that leaves only 13 mm below the pupil, should be refit in a deeper frame or a design made for short fittings, before the order goes out.

Minkwitz's theorem explains why short corridors feel harder: near the corridor, unwanted astigmatism grows sideways about twice as fast as the power changes along it, so packing the same add into less length narrows the clear zones.

When a new wearer reports swim or curved walls, first explain the expected peripheral blur and head movement, and verify the fitting height and monocular PDs before blaming the lens.

Check yourself

1. A patient chooses a small, shallow frame for progressive lenses. Why must the optician check the B measurement before ordering?

2. An optician is ordering a progressive lens. Which set of measurements must be taken on the patient in the adjusted, chosen frame?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), 21 CFR 801.410: Use of impact-resistant lenses in eyeglasses and sunglasses, eCFR: 21 CFR 801.410 (current text), OSHA 29 CFR 1910.133: Eye and face protection (ANSI Z87.1)

Optician (ABO) cheat sheet: every key fact on one page →