Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Back

Study guide · Chapter 5 of 7

Instruments & Verification Study Guide — Optician (ABO)

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

21 free practice questions

Verification questions ask how to read a finished lens correctly and what to do with the result. You need to know how to set up and read a lensmeter, how multifocals, progressives and prism are checked, what the lens clock and other dispensing instruments measure, and how a job is judged against the tolerances supplied in the question. When a stem gives a tolerance, apply that number exactly.

Key takeaways

  • Focus the lensmeter eyepiece for each operator, and read single-vision lenses with the concave side against the stop to get back vertex power.
  • The cylinder is the difference between the two focus readings, not the second reading itself.
  • Front-surface multifocal adds are read as front vertex power, and progressive prism is read at the prism reference point.
  • Prism is read as target displacement with the lens held where it will sit when worn; sliding the lens to center the target erases it.
  • Final inspection starts with power and axis and ends with cosmetics and frame alignment.

Lessons in this chapter

5 short lessons · 5 min read

  1. 1Setting up and reading a lensmeter1 min
  2. 2Verifying multifocals and progressives1 min
  3. 3Verifying prism and centration1 min
  4. 4The lens clock and other dispensing instruments1 min
  5. 5Tolerances and final inspection1 min
View all questions & answers →

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), 20/20 Magazine: Honing spectacle lens verification expertise (ANSI Z80.1 sphere tolerances, compensated powers), The Vision Council: Lens Marking Guidelines (34 mm engravings, prism reference point), 20/20 Magazine: Diopter 1.53, the lens measure convention

Optician (ABO) cheat sheet: every key fact on one page →Next chapter: Laws, Standards & Practice →

Practice questions based on the American Board of Opticianry Basic Certification exam content outline, standard ophthalmic dispensing references, and the federal rules that govern eyewear (the FDA impact-resistance requirement and the FTC Eyeglass and Contact Lens Rules). ABO and NCLE are marks of the American Board of Opticianry and National Contact Lens Examiners; this site is not affiliated with or endorsed by them. Opticianry is licensed in only some states and the requirements differ — confirm your own state board's practice act and the current exam format before testing. About the ABO exam →