Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Laws, Standards & Practice

Chapter 6 · Lesson 4 of 5

ANSI standards and safety eyewear

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

ANSI Z80.1, the prescription lens standard, is a voluntary consensus standard written by balanced committees, not a statute passed by a legislature.

It is still the accepted yardstick for a finished pair: it names the parameters to check and how far each may differ from the order before the job fails. The prescription decides what to make; Z80.1 decides how the result is judged.

Occupational protection is different. Prescription safety eyewear for hazards such as flying particles follows ANSI/ISEA Z87.1, a much more demanding impact standard than the federal dress-lens rule.

The lenses and the frame must each be marked to that standard, and the eye is only as protected as the weakest part: a rated lens in an unrated frame gives only the protection of the frame.

Under OSHA rules (29 CFR 1910.133), the employer must provide protection that meets the standard; the dispenser supplies a complete, correctly marked assembly. OSHA also allows a worker who wears glasses either safety eyewear that incorporates the prescription or protection worn over the glasses without disturbing their position.

Example: a welder's assistant asks for safety lenses to be put in his favorite dress frame. That combination is not rated safety eyewear, so he needs a frame marked to Z87.1 as well.

Check yourself

1. A patient needs prescription eyewear for work in a machine shop where flying particles are a hazard. Which statement correctly describes how this differs from dispensing ordinary dress eyewear?

2. A machine-shop employee who wears prescription glasses asks the optician whether he may simply wear his everyday dress glasses on the shop floor, where flying chips are a hazard. Under OSHA 29 CFR 1910.133, what must his employer ensure?

Facts checked 2026-11-15 · Sources: 21 CFR 801.410: Use of impact-resistant lenses in eyeglasses and sunglasses, 16 CFR Part 456: Ophthalmic Practice Rules (Eyeglass Rule), 16 CFR Part 315: Contact Lens Rule, eCFR: 16 CFR 456.4 Confirmation of prescription release, Federal Register: Ophthalmic Practice Rules (Eyeglass Rule) final rule, 89 FR 60742 (July 26, 2024), eCFR: 16 CFR 315.3 Availability of contact lens prescriptions to patients, OSHA: 29 CFR 1910.133 Eye and face protection

Optician (ABO) cheat sheet: every key fact on one page →