Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Ophthalmic Optics

Chapter 1 · Lesson 4 of 5

Cylinder power in any meridian

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

A spherical surface has the same curve in every meridian and brings light to a single point focus, so it corrects sphere only. A toric surface has two principal curves 90 degrees apart and forms two focal lines, which is what a lens needs to neutralize astigmatism.

In a sphero-cylinder, the sphere power lies along the axis meridian, and the full cylinder is added in the meridian 90 degrees away.

Between those two meridians, the power builds gradually. The working formula is F = sphere + cylinder × sin²θ, where θ is the angle between the meridian and the cylinder axis.

Angle from the axisShare of cylinder in effect
0 degrees (on the axis)None
30 degrees25 percent
45 degrees50 percent
60 degrees75 percent
90 degreesAll of it

Example: a lens of +1.00 −2.00 × 090. The 120 meridian is 30 degrees from the axis, and sin² 30° is 0.25, so a quarter of the cylinder acts there: +1.00 + (−2.00 × 0.25) = +0.50 D. The exam may give you the formula or the percentage rule; either way, measure the angle from the axis, not from 0 or 180.

Check yourself

1. How do a spherical surface and a toric surface differ, and what does each correct?

2. A lens is made to -2.00 -1.00 x 180. Using F = sphere + cylinder x sin squared of the angle from the axis, what power lies in the 060 meridian?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), ABO-NCLE Basic Exam Handbook (December 2023), OpenStax College Physics 2e: Image Formation by Lenses

Optician (ABO) cheat sheet: every key fact on one page →