Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Prescription Analysis & Math

Chapter 3 · Lesson 4 of 5

Prism, vertical imbalance and slab-off

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

Prentice's rule, prism = power × decentration in centimeters, works in both directions. To create prescribed prism by moving the optical center, divide: decentration in cm = prism ÷ power. Example: 2.00 prism diopters from a +5.00 D lens needs 2.00 ÷ 5.00 = 0.4 cm, which is 4 mm. Multiplying instead of dividing is the usual slip.

Between the two eyes, vertical prisms with opposite bases add, because base up in one eye and base down in the other move the images apart. Prisms with the same base in both eyes subtract. When the two eyes have different vertical powers, reading below the optical centers creates a vertical imbalance even with no prism prescribed.

Example: OD +1.00 DS and OS +3.50 DS, reading 9 mm below both optical centers.

The right lens gives 0.9 × 1.00 = 0.90 and the left 0.9 × 3.50 = 3.15 prism diopters, both base up because plus lenses viewed below the center have their base toward it. Same base, so subtract: 3.15 − 0.90 = 2.25 prism diopters of imbalance.

Conventional slab-off adds base-up prism to the reading area and goes on the more minus, or less plus, lens; a reverse slab adds base-down prism and goes on the more plus lens, here the left.

Check yourself

1. A wearer has OD +2.50 DS and OS -1.00 DS in single-vision glasses with 4 mm of pantoscopic tilt already set. When reading, the eyes look 10 mm below both distance optical centers. What vertical prismatic imbalance is created at the reading level?

2. A wearer has OD -1.00 DS and OS -4.00 DS, and the reading point lies 10 mm directly below both distance optical centers. What vertical prismatic imbalance exists between the two eyes at the reading point?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE)

Optician (ABO) cheat sheet: every key fact on one page →