Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Frames, Measuring & Fitting

Chapter 4 · Lesson 4 of 5

Measuring for multifocals and progressives

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

Measurements describe where each pupil sits behind the lens, and that changes whenever the frame moves. So the frame is adjusted first, then monocular PDs and heights are taken in the position of wear, with the optician's eyes level with the patient's.

Monocular values are preferred because faces are rarely symmetric; splitting one binocular PD can put one center nasal and the other temporal to its pupil.

  • Segment inset per lens is half the difference between the distance and near PDs, because the convergence is shared by both eyes.
  • Segment height is measured from the lowest point of the lens; the geometric center lies at half the B measurement.
  • A trifocal's intermediate top is customarily set at the lower edge of the pupil, higher than a bifocal line.
  • A flat-top bifocal line is fitted at the lower lid margin, but on the finished lens its height is still measured up from the lowest point of the shape.

Example: distance PD 66 and near PD 62 give 4 mm total, so 2 mm of inset for each segment. In a frame with B = 36, a 16 mm segment height puts the segment top 18 − 16 = 2 mm below the geometric center.

Check yourself

1. Why are monocular distance measurements preferred over one binocular value when spectacle lenses are ordered?

2. At what point in the dispensing process are fitting heights and monocular distances taken?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), 20/20 Magazine: Martin's rule of tilt, 1 mm of optical center drop per 2 degrees of pantoscopic tilt, ABDO: Mo Jalie on fitting and pantoscopic tilt (PDF), Laramy-K Optical: polycarbonate and Trivex in drill mounts

Optician (ABO) cheat sheet: every key fact on one page →