Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Lens Products & Materials

Chapter 2 · Lesson 2 of 5

Coatings, tints and light control

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

The share of light reflected at each lens surface rises with refractive index. An untreated high-index lens therefore transmits less light and shows stronger reflections and ghost images than CR-39, which is why antireflective treatment becomes more important as the index goes up.

Tint darkness controls visible light, not ultraviolet. CR-39 blocks UVB but does not block all the way to 400 nm on its own, so a dark CR-39 sun lens needs a separate UV treatment. Without it, the dark lens widens the pupil and can let more UV reach the eye. Polycarbonate, Trivex and high-index materials block UV inherently.

  • Photochromic lenses are activated by ultraviolet. A car windshield absorbs most of it, so they darken little while driving, and heat makes them lighter.
  • Polarized lenses block the horizontally polarized glare reflected off water and roads, but they can darken liquid-crystal displays at some head angles.

Example: a gardener wants dark gray CR-39 sunglasses. The order should specify both the tint and a UV treatment, because the tint alone says nothing about UV.

Check yourself

1. A wearer orders a dark gray tint in CR-39, a material that does not block UV all the way to 400 nm on its own, for beach use. What else must be specified?

2. Why does antireflective treatment become more important as lens index increases?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), 21 CFR 801.410: Use of impact-resistant lenses in eyeglasses and sunglasses, eCFR: 21 CFR 801.410 (current text), OSHA 29 CFR 1910.133: Eye and face protection (ANSI Z87.1)

Optician (ABO) cheat sheet: every key fact on one page →