Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Instruments & Verification

Chapter 5 · Lesson 1 of 5

Setting up and reading a lensmeter

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

Before reading anything, focus the eyepiece for your own eye. Turn it to full plus, then back slowly until the reticle crosshairs just become sharp, with the power drum at zero.

If the eyepiece is set for someone else, your accommodation can bias every reading in the same direction, so two operators sharing one instrument may disagree by a constant amount until each refocuses.

A single-vision spectacle lens is verified as back vertex power, so the concave side rests against the lens stop. Reading in minus cylinder, turn the drum from plus toward minus.

Turn the axis wheel and the drum until the mires come sharp in the first principal meridian; that drum reading is the sphere, and the axis wheel setting at that moment is the axis. Keep turning until the mires focus in the second principal meridian; the cylinder is the second reading minus the first.

Example: the first meridian focuses at −0.75 with the axis wheel at 160, and the second focuses at −2.00. The cylinder is −2.00 − (−0.75) = −1.25, so the lens is −0.75 −1.25 × 160. If the mires focus at a single drum reading and stay sharp through a full turn of the axis wheel, the lens is a sphere.

Check yourself

1. Reading a lens in minus cylinder on a manual lensmeter, the operator focuses the single sphere lines at -1.75 with the axis wheel at 030, then focuses the close-set lines at -4.25. What is the power of the lens?

2. Two opticians share one manual lensmeter, and the second reads nearly every job about 0.50 D more minus than the first. Nothing else on the instrument has been altered. What explains the difference, and what is the fix?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), 20/20 Magazine: Honing spectacle lens verification expertise (ANSI Z80.1 sphere tolerances, compensated powers), The Vision Council: Lens Marking Guidelines (34 mm engravings, prism reference point), 20/20 Magazine: Diopter 1.53, the lens measure convention

Optician (ABO) cheat sheet: every key fact on one page →