Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Instruments & Verification

Chapter 5 · Lesson 5 of 5

Tolerances and final inspection

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

Finished prescription lenses are judged against ANSI Z80.1, the voluntary consensus standard for prescription lenses. The exam generally supplies the tolerance figures in the question and asks you to apply them.

For reference, the single-vision sphere tolerance is plus or minus 0.13 D from −6.50 to +6.50 D and plus or minus 2 percent of the power beyond that. Remember the pattern behind the axis table: the allowed axis error gets smaller as cylinder power gets larger, because the same error costs more in a strong cylinder.

Example: a stem states a center thickness tolerance of plus or minus 0.3 mm for a lens ordered at 2.0 mm. A caliper reading of 2.2 mm is 0.2 mm over and passes; a reading of 2.4 mm is 0.4 mm over and the job goes back.

Segment and fitting heights are measured from the lowest point of the boxed lens shape up to the segment top or fitting cross.

  • Final inspection order: sphere, cylinder and axis; then the add and any prism; then optical center placement and heights.
  • Last come cosmetic condition and standard bench alignment, so no work is wasted on a pair that must go back for power.

Check yourself

1. An optician carries out final inspection on a finished pair before dispensing. Which sequence follows the standard order of that inspection?

2. A segment height of 18 mm is ordered on a flat-top bifocal. On the finished lens, from what reference is that 18 mm measured, and to what?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), 20/20 Magazine: Honing spectacle lens verification expertise (ANSI Z80.1 sphere tolerances, compensated powers), The Vision Council: Lens Marking Guidelines (34 mm engravings, prism reference point), 20/20 Magazine: Diopter 1.53, the lens measure convention

Optician (ABO) cheat sheet: every key fact on one page →