Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾

0 of 35 lessons finished

Continue: Prism and Prentice's rule
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Ophthalmic Optics

Chapter 1 · Lesson 2 of 5

Surface power and the lens measure

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

Each surface of a lens has its own power, F = (n − 1)/r, with the radius r in meters.

Example: a 125 mm radius on a 1.50 material gives 0.50/0.125 = +4.00 D. The same radius on a 1.60 material gives 0.60/0.125 = +4.80 D. Turned around, a higher index needs a longer radius, which means a flatter surface, for the same power.

In the thin-lens approximation, total lens power is the sum of the two surface powers. A +7.00 D front and a −4.00 D back give about +3.00 D. The true value is slightly more plus because center thickness adds a little, which is why laboratories compensate thickness on strong plus lenses.

A lens measure, or lens clock, reads the sag of a surface and converts it to power assuming an index of 1.53. On any other material, correct the dial: true power = reading × (n − 1)/0.53. Example: a reading of +4.00 on a 1.67 lens is 4.00 × 0.67/0.53, about +5.06 D. When the material index is above 1.53 the true power is greater than the dial, and when it is below 1.53, as with CR-39, the true power is smaller.

Check yourself

1. The front surface of a lens made from a material of index 1.50 has a radius of curvature of 100 mm. What is the power of that surface?

2. A lens has a front surface power of +8.00 D and a back surface power of -5.50 D. Using the approximate thin-lens relationship, what is the power of the lens?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), ABO-NCLE Basic Exam Handbook (December 2023), OpenStax College Physics 2e: Image Formation by Lenses

Optician (ABO) cheat sheet: every key fact on one page →