Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾

0 of 35 lessons finished

Continue: Temples, bridges and pads
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Frames, Measuring & Fitting

Chapter 4 · Lesson 1 of 5

Frame materials and how they behave

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

Each material reacts to heat and stress in its own way, and exam questions turn on that behavior. Cellulose acetate, or zyl, is a thermoplastic: warm it evenly, form the new bend, and hold it until it cools, or it creeps back.

Bending it cold can snap it, and overheating blisters the surface. Because acetate softens slightly at skin temperature, a frame that fits in the morning but slides by afternoon has usually relaxed at the ear bends and needs them reformed.

  • Epoxy resin is thermosetting with shape memory: reheating sends it back toward its molded shape, so adjust it warm and hold it until cool.
  • Polyamide (nylon) cannot be soldered, because solder bonds only metals and the torch would distort the polymer; a cracked front is replaced.
  • Monel contains nickel, the usual cause of a contact rash where pads and end pieces touch the skin; switch to titanium or stainless steel.
  • Drilled rimless mountings are normally made in polycarbonate or Trivex, the standard choices because their toughness resists cracking at the hole; glass and brittle resins tend to chip or star-crack there.

Check yourself

1. Six weeks after dispensing a Monel frame, a patient returns with itching and a red rash exactly where the pads and end pieces touch the skin. What is the appropriate response?

2. The eyewire of a polyamide (nylon) sports frame has cracked through at the lower rim. The wearer asks whether the break can be soldered. What should be done?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), 20/20 Magazine: Martin's rule of tilt, 1 mm of optical center drop per 2 degrees of pantoscopic tilt, ABDO: Mo Jalie on fitting and pantoscopic tilt (PDF), Laramy-K Optical: polycarbonate and Trivex in drill mounts

Optician (ABO) cheat sheet: every key fact on one page →