Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Lens Products & Materials

Chapter 2 · Lesson 5 of 5

High-power designs and impact testing

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

An aspheric surface flattens gradually away from its center. On a high plus lens, such as an aphakic correction, that allows a flatter base with less center thickness and weight, controls the off-axis astigmatism of a steep curve, and makes the wearer's eyes look less magnified.

For extreme powers, a lenticular design puts the prescription in a small central aperture surrounded by a thin, low-power carrier, at the cost of a visible edge and a limited field.

TestWhat it involves
FDA dress-lens drop ball (21 CFR 801.410)A 5/8-inch steel ball of about 0.56 ounce dropped 50 inches onto the upper surface; the lens must not fracture
ANSI Z87.1 high-impact safety lensAt least 2.0 mm thick, a high-velocity 1/4-inch ball test, and the maker's mark followed by a plus sign

Under the FDA rule, every finished glass prescription lens must be tested individually, while plastic and other impact-resistant lenses may be qualified by testing a statistically significant sample from each production batch. A prescriber who finds an impact-resistant lens unsuitable for a patient must direct other lenses in writing and notify the patient in writing.

Check yourself

1. A laboratory tests a finished glass dress lens for impact resistance under the FDA regulation. What does that test use?

2. Under the FDA impact-resistance regulation for eyeglass lenses, how must finished prescription lenses be shown to withstand the drop-ball test?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), 21 CFR 801.410: Use of impact-resistant lenses in eyeglasses and sunglasses, eCFR: 21 CFR 801.410 (current text), OSHA 29 CFR 1910.133: Eye and face protection (ANSI Z87.1)

Optician (ABO) cheat sheet: every key fact on one page →