Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Prescription Analysis & Math

Chapter 3 · Lesson 5 of 5

Decentration, blank size, vertex and tilt

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

The frame PD, or geometric center distance, is the A measurement plus the DBL. Total decentration is the frame PD minus the wearer's PD, shared between the two lenses.

Minimum blank size is the effective diameter plus twice the per-lens decentration plus about 2 mm for edging; decentration counts twice because the blank must reach farther on the side the optical center moves away from.

Example: a 50-19 frame with a 54 mm effective diameter and a 63 mm PD. Frame PD = 50 + 19 = 69 mm, total decentration = 69 − 63 = 6 mm, so 3 mm in per lens. Minimum blank = 54 + 6 + 2 = 62 mm.

Vertex compensation uses F/(1 − dF), with d in meters, positive when the lens moves closer. A −10.00 D lens moved 3 mm closer gives −10.00 ÷ 1.03 = −9.71, ordered as −9.75 D: a minus lens moved closer needs less minus.

For pantoscopic tilt, the optical center is lowered about 1 mm below the pupil for every 2 degrees, so 6 degrees calls for about a 3 mm drop. That keeps the lens's optical axis passing through the eye's center of rotation.

Check yourself

1. A frame has an eyesize (A measurement) of 54 mm, a distance between lenses of 16 mm and an effective diameter of 58 mm, and the wearer's distance pupillary distance is 62 mm. Allowing 2 mm for edging, what is the minimum blank size required?

2. A frame has an eyesize (A measurement) of 52 mm and a distance between lenses of 18 mm, and the wearer's distance pupillary distance is 62 mm. How much must each lens be decentred, and in which direction?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE)

Optician (ABO) cheat sheet: every key fact on one page →