Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Lens Products & Materials

Chapter 2 · Lesson 1 of 5

Choosing a lens material

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

Three properties do different jobs. Refractive index sets thickness, because a higher index reaches the same power with flatter curves. Specific gravity, a material's density compared with water, sets weight. Abbe value sets how much color fringing the wearer sees away from the optical center, and it generally falls as index rises.

MaterialIndexWhat it is known for
CR-39About 1.50Good optics, but not high impact and brittle at a drill hole
Trivex1.53Lightest standard material (specific gravity about 1.11) and high impact
Polycarbonate1.586High impact, specific gravity about 1.20, inherent UV blocking
High index1.67 to 1.74Thinnest edges, but lower Abbe value and more surface reflection

Example: a 12-year-old basketball player needs −2.25 in each eye and asks for the thinnest lens. At that power the edge difference between polycarbonate and 1.67 is small, while the impact difference is not, so polycarbonate or Trivex is the answer.

The same logic covers a patient with one seeing eye: both lenses, even a plano balance lens, go in a high-impact material.

Check yourself

1. Two pairs are made to the same Rx and frame size, one in Trivex (specific gravity about 1.11) and one in polycarbonate (about 1.20). What will the wearer notice?

2. A wearer at -6.00 DS asks whether switching from CR-39 to Trivex will noticeably thin his lens edges. What is the accurate answer?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), 21 CFR 801.410: Use of impact-resistant lenses in eyeglasses and sunglasses, eCFR: 21 CFR 801.410 (current text), OSHA 29 CFR 1910.133: Eye and face protection (ANSI Z87.1)

Optician (ABO) cheat sheet: every key fact on one page →