Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Instruments & Verification

Chapter 5 · Lesson 2 of 5

Verifying multifocals and progressives

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

A conventional segment ground on the front surface is checked as front vertex power. Turn the lens around so the convex side faces the stop, then take both the distance reading and the segment reading that way.

The add is the difference. If you read a front-surface segment in back vertex orientation, the add comes out too high, and the error grows with plus power.

Example: with the convex side down, a plus lens reads +1.50 in the distance area and +3.50 in the segment, so the add is +2.00. That is the figure compared with the order.

A progressive has no visible landmarks once the ink is removed, so it is remarked from its permanent engravings using the maker's chart.

The two alignment engravings sit 34 mm apart on a horizontal line, and the engraved marks often also identify the brand and add power. Line them up on the chart, then redraw the fitting cross, the distance and near circles and the prism reference point.

  • Distance power: read in the distance verification circle above the fitting cross.
  • Add: read in the near reference circle.
  • Prism: read at the prism reference point, midway between the engravings.

Digitally surfaced lenses may come with compensated powers for the position of wear. When they do, the lens is verified against those compensated values, not the written prescription.

Check yourself

1. A flat-top bifocal in a plus prescription is being verified. With the back surface on the stop the distance portion reads +2.00 and the segment reads +4.10, so the optician records a +2.10 add against the +2.00 ordered. What is wrong here?

2. A progressive lens has been remarked from its permanent engravings, which sit 34 mm apart. Which reference is used for the distance power, and which for prescribed prism?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), 20/20 Magazine: Honing spectacle lens verification expertise (ANSI Z80.1 sphere tolerances, compensated powers), The Vision Council: Lens Marking Guidelines (34 mm engravings, prism reference point), 20/20 Magazine: Diopter 1.53, the lens measure convention

Optician (ABO) cheat sheet: every key fact on one page →