Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/35 ▾
  1. 1.Ophthalmic Optics0/5
    1. Refractive index and lens power
    2. Surface power and the lens measure
    3. Prism and Prentice's rule
    4. Cylinder power in any meridian
    5. Aberrations, Abbe value and vertex distance
  2. 2.Lens Products & Materials0/5
    1. Choosing a lens material
    2. Coatings, tints and light control
    3. Bifocal and trifocal segments
    4. Progressive lenses
    5. High-power designs and impact testing
  3. 3.Prescription Analysis & Math0/5
    1. Reading and transposing a prescription
    2. Meridian powers and spherical equivalent
    3. Near and intermediate powers from the add
    4. Prism, vertical imbalance and slab-off
    5. Decentration, blank size, vertex and tilt
  4. 4.Frames, Measuring & Fitting0/5
    1. Frame materials and how they behave
    2. Temples, bridges and pads
    3. The boxing system, decentration and blank size
    4. Measuring for multifocals and progressives
    5. Pantoscopic tilt and bench alignment
  5. 5.Instruments & Verification0/5
    1. Setting up and reading a lensmeter
    2. Verifying multifocals and progressives
    3. Verifying prism and centration
    4. The lens clock and other dispensing instruments
    5. Tolerances and final inspection
  6. 6.Laws, Standards & Practice0/5
    1. The FDA impact-resistance rule
    2. The FTC Eyeglass Rule
    3. The FTC Contact Lens Rule
    4. ANSI standards and safety eyewear
    5. Scope of practice, privacy and referral
  7. 7.Ocular Anatomy & Pathology0/5
    1. The front of the eye: cornea, aqueous humor and tear drainage
    2. The crystalline lens: accommodation, aphakia and pseudophakia
    3. The retina, the optic nerve and the visual pathway
    4. Eye diseases an optician must recognize and refer
    5. Visual acuity, astigmatism types and binocular vision
Saved in this browser. Move it to another device →
← Frames, Measuring & Fitting

Chapter 4 · Lesson 5 of 5

Pantoscopic tilt and bench alignment

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

The customary rule pairs 1 mm of optical center drop below the pupil with every 2 degrees of pantoscopic tilt.

Matching them keeps the lens's optical axis through the eye's center of rotation, so the wearer looks through the lens at the angles it was designed for. Example: a frame with 12 degrees of tilt calls for about a 6 mm drop; a 3 mm drop pairs with 6 degrees.

  • Temple parallelism: set the frame upside down with the temples open; both temples should touch the flat surface at once.
  • Coplanar alignment: seen from above, both lens planes should lie in one plane.
  • X-ing is a twist seen from the side, and a skewed front is a rotation seen from the front.

Frame choice affects lenses too. For a strong minus prescription, a small, round shape with a frame PD close to the wearer's keeps every edge near the optical center and decentration small, which gives the thinnest edges.

Check yourself

1. An optician checks an adjusted frame for temple parallelism on a flat bench. How is that check performed, and what does it show?

2. The laboratory has placed the distance optical centers 4 mm below the wearer's pupil centers. Using the customary rule of 1 mm of drop for every 2 degrees of tilt, how much pantoscopic tilt should the frame carry?

Facts checked 2026-11-15 · Sources: American Board of Opticianry and National Contact Lens Examiners (ABO-NCLE), 20/20 Magazine: Martin's rule of tilt, 1 mm of optical center drop per 2 degrees of pantoscopic tilt, ABDO: Mo Jalie on fitting and pantoscopic tilt (PDF), Laramy-K Optical: polycarbonate and Trivex in drill mounts

Optician (ABO) cheat sheet: every key fact on one page →