Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/32 ▾
  1. 1.Electrical Maintenance & Repair0/4
    1. Overloads, short circuits and ground faults
    2. Wiring receptacles, switches and fixtures
    3. Working safely: de-energize, test, then touch
    4. Ohm's law, Watt's law and the multimeter
  2. 2.Plumbing Maintenance & Repair0/4
    1. Supply, distribution and drainage: traps and vents
    2. Shutoffs, leaks and water damage
    3. Toilets, faucets and clearing drains
    4. Water heaters and joining pipe
  3. 3.HVAC Service & When to Refer0/5
    1. Airflow: filters, returns, registers and coils
    2. Condensate drains, pans and float switches
    3. Thermostats and controls
    4. The refrigeration cycle, superheat and EPA Section 608
    5. Furnaces, heat pumps, boilers and gas safety
  4. 4.Appliances, Locks & Keys0/5
    1. Refrigerators: moving heat out of the box
    2. Kitchen appliances: ranges, dishwashers, disposals and hoods
    3. Washers and dryers
    4. Reading schematics and testing parts
    5. Locks, keys and lockouts
  5. 5.Interior & Exterior Repair0/5
    1. Drywall repair
    2. Primer, paint and sheen
    3. Texture and caulk
    4. Doors, windows, cabinets and floors
    5. Exterior, ladders and suspect materials
  6. 6.Compliance, Safety & Fair Housing0/4
    1. Chemicals, PPE and sharps
    2. Lockout/tagout, confined spaces and ladders
    3. Fair housing in maintenance work
    4. Lead, asbestos, mold, pests and records
  7. 7.Facilities Operations & Professionalism0/5
    1. Prioritizing service requests and entering homes
    2. Make-ready turns, inspections and curb appeal
    3. Preventive maintenance, repair or replace, and contractors
    4. Pool and spa chemistry and math
    5. Life safety, reporting and records
Saved in this browser. Move it to another device →
← Plumbing Maintenance & Repair

Chapter 2 · Lesson 2 of 4

Shutoffs, leaks and water damage

1 min read

When water is escaping, stop it at the closest point of control first. The angle stop under a sink or toilet isolates one fixture in seconds without cutting water to other homes.

If that stop is corroded and will not close, go up one level to the unit or branch valve, then to the riser or building main. Forcing a corroded stop can snap the stem and turn a small leak into a flood. Containment, photos and the repair all come after the flow stops.

  • Wet building materials can start growing mold within a day or two, so a soft, stained ceiling is reported right away and drying starts the same day.
  • A pipe with no water in it cannot burst. Before winter, isolate, drain and insulate exposed hose bibbs and unheated piping.
  • A hose end lying in a sink of used water is a cross-connection: a pressure drop could siphon that water back into the drinking supply. An air gap or a vacuum breaker prevents it.

Example: a supply line bursts under a bathroom sink and the angle stop turns but water keeps coming. The technician closes the valve that serves the whole apartment, which stops the flow while leaving neighbors in service, and then replaces the failed stop before restoring water.

Check yourself

1. Water is spraying from a supply line under a kitchen sink while the resident stands by. What should the technician do FIRST?

2. The angle stop under a leaking toilet is corroded and will not close all the way. What should the technician do NEXT?

Facts checked 2026-11-15 · Sources: NAAEI: Certificate for Apartment Maintenance Technicians (CAMT), EPA: Mold and moisture (dry wet materials within 24 to 48 hours)

CAMT Apartment Maintenance cheat sheet: every key fact on one page →