Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/32 ▾
  1. 1.Electrical Maintenance & Repair0/4
    1. Overloads, short circuits and ground faults
    2. Wiring receptacles, switches and fixtures
    3. Working safely: de-energize, test, then touch
    4. Ohm's law, Watt's law and the multimeter
  2. 2.Plumbing Maintenance & Repair0/4
    1. Supply, distribution and drainage: traps and vents
    2. Shutoffs, leaks and water damage
    3. Toilets, faucets and clearing drains
    4. Water heaters and joining pipe
  3. 3.HVAC Service & When to Refer0/5
    1. Airflow: filters, returns, registers and coils
    2. Condensate drains, pans and float switches
    3. Thermostats and controls
    4. The refrigeration cycle, superheat and EPA Section 608
    5. Furnaces, heat pumps, boilers and gas safety
  4. 4.Appliances, Locks & Keys0/5
    1. Refrigerators: moving heat out of the box
    2. Kitchen appliances: ranges, dishwashers, disposals and hoods
    3. Washers and dryers
    4. Reading schematics and testing parts
    5. Locks, keys and lockouts
  5. 5.Interior & Exterior Repair0/5
    1. Drywall repair
    2. Primer, paint and sheen
    3. Texture and caulk
    4. Doors, windows, cabinets and floors
    5. Exterior, ladders and suspect materials
  6. 6.Compliance, Safety & Fair Housing0/4
    1. Chemicals, PPE and sharps
    2. Lockout/tagout, confined spaces and ladders
    3. Fair housing in maintenance work
    4. Lead, asbestos, mold, pests and records
  7. 7.Facilities Operations & Professionalism0/5
    1. Prioritizing service requests and entering homes
    2. Make-ready turns, inspections and curb appeal
    3. Preventive maintenance, repair or replace, and contractors
    4. Pool and spa chemistry and math
    5. Life safety, reporting and records
Saved in this browser. Move it to another device →
← HVAC Service & When to Refer

Chapter 3 · Lesson 5 of 5

Furnaces, heat pumps, boilers and gas safety

1 min read

In an induced-draft gas furnace, the first event after a call for heat is the inducer motor starting, and a pressure switch proves the vent is drawing.

Only then does the igniter heat, the gas valve open and the burners light. The flame sensor proves flame, and the blower starts after a short delay so it does not push cold air into the home.

  • A heat pump that stops its outdoor fan for a few minutes while steam rises from the coil is in a normal defrost cycle.
  • A cold top-floor baseboard with gurgling pipes has trapped air; bleed it at the baseboard bleeder valve.
  • A brief burning-dust smell on the first heating run of the season, with warm supply air, is normal.

Two situations are never service adjustments. A gas smell means an ignitable mixture may be present, so the technician uses no switches, phones or radios, gets everyone out and calls from outside.

A carbon monoxide alarm together with soot or a yellow, rolling flame means incomplete combustion: shut the furnace down, ventilate and leave it off until a licensed contractor evaluates it.

Check yourself

1. While checking a gas furnace in an occupied apartment, a technician smells gas near the equipment. What is the correct sequence of actions?

2. A resident's thermostat calls for heat on an induced-draft gas furnace with hot surface ignition. Which event should happen first in the furnace's normal sequence of operation?

Facts checked 2026-11-15 · Sources: NAAEI: Certificate for Apartment Maintenance Technicians (CAMT), EPA: Section 608 of the Clean Air Act (refrigerant management), EPA: Universal waste (mercury-containing equipment)

CAMT Apartment Maintenance cheat sheet: every key fact on one page →