Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/32 ▾
  1. 1.Electrical Maintenance & Repair0/4
    1. Overloads, short circuits and ground faults
    2. Wiring receptacles, switches and fixtures
    3. Working safely: de-energize, test, then touch
    4. Ohm's law, Watt's law and the multimeter
  2. 2.Plumbing Maintenance & Repair0/4
    1. Supply, distribution and drainage: traps and vents
    2. Shutoffs, leaks and water damage
    3. Toilets, faucets and clearing drains
    4. Water heaters and joining pipe
  3. 3.HVAC Service & When to Refer0/5
    1. Airflow: filters, returns, registers and coils
    2. Condensate drains, pans and float switches
    3. Thermostats and controls
    4. The refrigeration cycle, superheat and EPA Section 608
    5. Furnaces, heat pumps, boilers and gas safety
  4. 4.Appliances, Locks & Keys0/5
    1. Refrigerators: moving heat out of the box
    2. Kitchen appliances: ranges, dishwashers, disposals and hoods
    3. Washers and dryers
    4. Reading schematics and testing parts
    5. Locks, keys and lockouts
  5. 5.Interior & Exterior Repair0/5
    1. Drywall repair
    2. Primer, paint and sheen
    3. Texture and caulk
    4. Doors, windows, cabinets and floors
    5. Exterior, ladders and suspect materials
  6. 6.Compliance, Safety & Fair Housing0/4
    1. Chemicals, PPE and sharps
    2. Lockout/tagout, confined spaces and ladders
    3. Fair housing in maintenance work
    4. Lead, asbestos, mold, pests and records
  7. 7.Facilities Operations & Professionalism0/5
    1. Prioritizing service requests and entering homes
    2. Make-ready turns, inspections and curb appeal
    3. Preventive maintenance, repair or replace, and contractors
    4. Pool and spa chemistry and math
    5. Life safety, reporting and records
Saved in this browser. Move it to another device →
← Electrical Maintenance & Repair

Chapter 1 · Lesson 2 of 4

Wiring receptacles, switches and fixtures

1 min read

In normal use, current leaves the panel on the hot conductor and returns on the grounded conductor, called the neutral. The equipment grounding conductor and bonding tie all metal boxes and enclosures together so that a fault has a low-resistance path back to the source and the breaker can open.

The ground carries current only during a fault, so it is never joined to the neutral at a receptacle or used as a return path. If it were, normal working current would flow over metal parts a person can touch.

  • Receptacle terminals: silver takes the white neutral, brass takes the black hot, green takes the ground. This keeps polarity correct.
  • A white conductor wrapped with black tape has been re-identified as a hot. Color is only a hint, so confirm with a tester before touching it.
  • A light controlled from two places uses a pair of three-way switches, each with three screw terminals: one common and two travelers.
  • Conductors that are too short get pigtails of the same gauge and color, and every splice stays inside a covered box.

Lighting failures follow the same logic. A fluorescent fixture that hums loudly and leaks dark oily residue points to a failing ballast. An integrated LED fixture has no ballast or starter; its power comes through a driver, so flickering followed by darkness usually means the driver has failed.

Check yourself

1. A technician is replacing a damaged duplex receptacle in an apartment. Where does each conductor land on the new device?

2. Which statement correctly describes the roles of the grounded (neutral) conductor and of bonding?

Facts checked 2026-11-15 · Sources: NAAEI: Certificate for Apartment Maintenance Technicians (CAMT), OSHA 29 CFR 1910.147: Control of hazardous energy (lockout/tagout)

CAMT Apartment Maintenance cheat sheet: every key fact on one page →