Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/32 ▾
  1. 1.Electrical Maintenance & Repair0/4
    1. Overloads, short circuits and ground faults
    2. Wiring receptacles, switches and fixtures
    3. Working safely: de-energize, test, then touch
    4. Ohm's law, Watt's law and the multimeter
  2. 2.Plumbing Maintenance & Repair0/4
    1. Supply, distribution and drainage: traps and vents
    2. Shutoffs, leaks and water damage
    3. Toilets, faucets and clearing drains
    4. Water heaters and joining pipe
  3. 3.HVAC Service & When to Refer0/5
    1. Airflow: filters, returns, registers and coils
    2. Condensate drains, pans and float switches
    3. Thermostats and controls
    4. The refrigeration cycle, superheat and EPA Section 608
    5. Furnaces, heat pumps, boilers and gas safety
  4. 4.Appliances, Locks & Keys0/5
    1. Refrigerators: moving heat out of the box
    2. Kitchen appliances: ranges, dishwashers, disposals and hoods
    3. Washers and dryers
    4. Reading schematics and testing parts
    5. Locks, keys and lockouts
  5. 5.Interior & Exterior Repair0/5
    1. Drywall repair
    2. Primer, paint and sheen
    3. Texture and caulk
    4. Doors, windows, cabinets and floors
    5. Exterior, ladders and suspect materials
  6. 6.Compliance, Safety & Fair Housing0/4
    1. Chemicals, PPE and sharps
    2. Lockout/tagout, confined spaces and ladders
    3. Fair housing in maintenance work
    4. Lead, asbestos, mold, pests and records
  7. 7.Facilities Operations & Professionalism0/5
    1. Prioritizing service requests and entering homes
    2. Make-ready turns, inspections and curb appeal
    3. Preventive maintenance, repair or replace, and contractors
    4. Pool and spa chemistry and math
    5. Life safety, reporting and records
Saved in this browser. Move it to another device →
← Interior & Exterior Repair

Chapter 5 · Lesson 3 of 5

Texture and caulk

1 min read

Texture goes on only after the drywall repair is finished, and the pattern depends on how thin the material is mixed and how it is applied, so the technician tests on scrap first to match an orange-peel wall.

Knockdown is made by spattering thinned compound, waiting until the wet sheen fades and the blobs begin to set, then skimming the tops lightly with a wide knife. Flattening at once smears the pattern, and sanding dry spatter only leaves a gritty look.

JointRight sealant
Tub to tile surroundSilicone: watertight and mildew resistant, but not paintable
Baseboard or trim that will be paintedSiliconized acrylic latex caulk
Wide exterior joint that moves with the seasonsBacker rod, then a flexible exterior-rated sealant

A backer rod sets the sealant depth and keeps the bead from sticking to the back of the joint, so it bonds on two faces and can stretch.

When a tub bead turns black with mildew, all the old caulk and residue are removed, the joint is cleaned and left to dry fully, and only then is a new bead applied. New silicone will not bond to old silicone.

Check yourself

1. Which sealant belongs at the joint between a bathtub and its tile surround?

2. A technician is matching a knockdown texture on a patched wall. What is the correct sequence for applying it?

Facts checked 2026-11-15 · Sources: NAAEI: Certificate for Apartment Maintenance Technicians (CAMT), EPA: Protect your family from exposures to asbestos

CAMT Apartment Maintenance cheat sheet: every key fact on one page →