Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/32 ▾

0 of 32 lessons finished

Continue: Locks, keys and lockouts
  1. 1.Electrical Maintenance & Repair0/4
    1. Overloads, short circuits and ground faults
    2. Wiring receptacles, switches and fixtures
    3. Working safely: de-energize, test, then touch
    4. Ohm's law, Watt's law and the multimeter
  2. 2.Plumbing Maintenance & Repair0/4
    1. Supply, distribution and drainage: traps and vents
    2. Shutoffs, leaks and water damage
    3. Toilets, faucets and clearing drains
    4. Water heaters and joining pipe
  3. 3.HVAC Service & When to Refer0/5
    1. Airflow: filters, returns, registers and coils
    2. Condensate drains, pans and float switches
    3. Thermostats and controls
    4. The refrigeration cycle, superheat and EPA Section 608
    5. Furnaces, heat pumps, boilers and gas safety
  4. 4.Appliances, Locks & Keys0/5
    1. Refrigerators: moving heat out of the box
    2. Kitchen appliances: ranges, dishwashers, disposals and hoods
    3. Washers and dryers
    4. Reading schematics and testing parts
    5. Locks, keys and lockouts
  5. 5.Interior & Exterior Repair0/5
    1. Drywall repair
    2. Primer, paint and sheen
    3. Texture and caulk
    4. Doors, windows, cabinets and floors
    5. Exterior, ladders and suspect materials
  6. 6.Compliance, Safety & Fair Housing0/4
    1. Chemicals, PPE and sharps
    2. Lockout/tagout, confined spaces and ladders
    3. Fair housing in maintenance work
    4. Lead, asbestos, mold, pests and records
  7. 7.Facilities Operations & Professionalism0/5
    1. Prioritizing service requests and entering homes
    2. Make-ready turns, inspections and curb appeal
    3. Preventive maintenance, repair or replace, and contractors
    4. Pool and spa chemistry and math
    5. Life safety, reporting and records
Saved in this browser. Move it to another device →
← Appliances, Locks & Keys

Chapter 4 · Lesson 4 of 5

Reading schematics and testing parts

1 min read

Schematic questions use two rules. If one load fails while the others run, the fault is in a part that only that load's path depends on, because every part the working loads share has just proved itself good.

If every load is dead, including the timer motor, the fault is in the part all of them share, such as a door latch switch wired ahead of everything. A timer sequence chart works the same way: the contact that closes only during the failing step is checked first.

To test a part, unplug the appliance and remove at least one wire from the part, so the meter does not read parallel paths through other components.

Example: a heating element rated 1,500 W at 120 V draws 1,500 ÷ 120 = 12.5 A, so its resistance should be about 120 ÷ 12.5 = 9.6 ohms. A reading of OL means the element is open. A reading equal to the amps or the watts is a planted wrong answer.

Example: a washer fills and agitates, but never spins. On the timer chart, one contact closes in agitate and spin, and another closes only in spin. Agitation proves the shared contact can close, so the spin-only contact is tested for continuity first, with the washer unplugged.

Check yourself

1. Nothing on a dishwasher works: it does not fill, the motor does not run, and the timer does not advance. The technician measured 120 V at the dishwasher's terminal block, then shut off the breaker and verified the unit was dead. The schematic shows L1 passing through the door latch switch before it reaches the timer motor and every timer contact. Which component should be tested first?

2. A top-load washer fills and agitates normally, but the tub never spins at the end of the cycle. The lid switch has already tested good. On the timer sequence chart, Contact 1 is closed only during fill, Contact 2 is closed during both agitate and spin, Contact 3 is closed only during the spin increments, and the timer motor contact is closed in every increment. With the washer unplugged, which contact should be checked first?

Facts checked 2026-11-15 · Sources: NAAEI: Certificate for Apartment Maintenance Technicians (CAMT), EPA: Section 608 of the Clean Air Act (refrigerant management)

CAMT Apartment Maintenance cheat sheet: every key fact on one page →