Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/32 ▾
  1. 1.Electrical Maintenance & Repair0/4
    1. Overloads, short circuits and ground faults
    2. Wiring receptacles, switches and fixtures
    3. Working safely: de-energize, test, then touch
    4. Ohm's law, Watt's law and the multimeter
  2. 2.Plumbing Maintenance & Repair0/4
    1. Supply, distribution and drainage: traps and vents
    2. Shutoffs, leaks and water damage
    3. Toilets, faucets and clearing drains
    4. Water heaters and joining pipe
  3. 3.HVAC Service & When to Refer0/5
    1. Airflow: filters, returns, registers and coils
    2. Condensate drains, pans and float switches
    3. Thermostats and controls
    4. The refrigeration cycle, superheat and EPA Section 608
    5. Furnaces, heat pumps, boilers and gas safety
  4. 4.Appliances, Locks & Keys0/5
    1. Refrigerators: moving heat out of the box
    2. Kitchen appliances: ranges, dishwashers, disposals and hoods
    3. Washers and dryers
    4. Reading schematics and testing parts
    5. Locks, keys and lockouts
  5. 5.Interior & Exterior Repair0/5
    1. Drywall repair
    2. Primer, paint and sheen
    3. Texture and caulk
    4. Doors, windows, cabinets and floors
    5. Exterior, ladders and suspect materials
  6. 6.Compliance, Safety & Fair Housing0/4
    1. Chemicals, PPE and sharps
    2. Lockout/tagout, confined spaces and ladders
    3. Fair housing in maintenance work
    4. Lead, asbestos, mold, pests and records
  7. 7.Facilities Operations & Professionalism0/5
    1. Prioritizing service requests and entering homes
    2. Make-ready turns, inspections and curb appeal
    3. Preventive maintenance, repair or replace, and contractors
    4. Pool and spa chemistry and math
    5. Life safety, reporting and records
Saved in this browser. Move it to another device →
← Interior & Exterior Repair

Chapter 5 · Lesson 4 of 5

Doors, windows, cabinets and floors

1 min read

These questions reward adjusting the part that was built to be adjusted, instead of cutting or planing something permanently. The top hinge carries most of a door's weight, so when its screws lose their grip the door sags and the top of the latch side rubs the frame; re-secure that hinge with screws long enough to reach the framing.

When the latch bolt hits just below the strike opening, move the strike plate or file its opening so it lines up. Planing the door leaves a permanent gap.

  • A window painted shut is freed by cutting the paint film between the sash and the stops, not by prying.
  • A crooked cabinet door is squared up with the adjustment screws in its hinges.
  • A soft, springy floor near a tub means the subfloor has lost strength to water. Stop the leak, cut out and replace the damaged decking, then lay the new floor.

Example: a bedroom door rubs the frame at the top corner on the knob side. The technician tightens the top hinge screws and finds two spinning in stripped holes, replaces them with longer screws that bite into the stud, and the door swings clear without any planing.

Check yourself

1. An entry door rubs the frame at the upper corner of the latch side. What is the most likely cause?

2. A door closes but the latch will not catch, and the bolt is marking the strike plate just below its opening. What is the correct fix?

Facts checked 2026-11-15 · Sources: NAAEI: Certificate for Apartment Maintenance Technicians (CAMT), EPA: Protect your family from exposures to asbestos

CAMT Apartment Maintenance cheat sheet: every key fact on one page →