Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/32 ▾
  1. 1.Electrical Maintenance & Repair0/4
    1. Overloads, short circuits and ground faults
    2. Wiring receptacles, switches and fixtures
    3. Working safely: de-energize, test, then touch
    4. Ohm's law, Watt's law and the multimeter
  2. 2.Plumbing Maintenance & Repair0/4
    1. Supply, distribution and drainage: traps and vents
    2. Shutoffs, leaks and water damage
    3. Toilets, faucets and clearing drains
    4. Water heaters and joining pipe
  3. 3.HVAC Service & When to Refer0/5
    1. Airflow: filters, returns, registers and coils
    2. Condensate drains, pans and float switches
    3. Thermostats and controls
    4. The refrigeration cycle, superheat and EPA Section 608
    5. Furnaces, heat pumps, boilers and gas safety
  4. 4.Appliances, Locks & Keys0/5
    1. Refrigerators: moving heat out of the box
    2. Kitchen appliances: ranges, dishwashers, disposals and hoods
    3. Washers and dryers
    4. Reading schematics and testing parts
    5. Locks, keys and lockouts
  5. 5.Interior & Exterior Repair0/5
    1. Drywall repair
    2. Primer, paint and sheen
    3. Texture and caulk
    4. Doors, windows, cabinets and floors
    5. Exterior, ladders and suspect materials
  6. 6.Compliance, Safety & Fair Housing0/4
    1. Chemicals, PPE and sharps
    2. Lockout/tagout, confined spaces and ladders
    3. Fair housing in maintenance work
    4. Lead, asbestos, mold, pests and records
  7. 7.Facilities Operations & Professionalism0/5
    1. Prioritizing service requests and entering homes
    2. Make-ready turns, inspections and curb appeal
    3. Preventive maintenance, repair or replace, and contractors
    4. Pool and spa chemistry and math
    5. Life safety, reporting and records
Saved in this browser. Move it to another device →
← Electrical Maintenance & Repair

Chapter 1 · Lesson 4 of 4

Ohm's law, Watt's law and the multimeter

1 min read

Two formulas cover the math questions. Watt's law says power equals voltage times current (P = E × I), so current is watts divided by volts. Ohm's law says voltage equals current times resistance (E = I × R), so resistance is volts divided by amps. Loads on the same circuit add together before you divide.

Example: a 3,600 W element runs on 240 V. Current is 3,600 ÷ 240 = 15 A, and resistance is 240 ÷ 15 = 16 ohms. Wrong answer choices usually come from dividing volts by watts, using 120 V when the question says 240 V, or reporting the amps as the resistance.

  • Measure ohms and continuity only with power off and the part disconnected, because the meter supplies its own test current.
  • OL on the ohms range means an open path, such as a broken heating element. A short reads at or near zero.
  • Example: a dryer element reads OL with power off and one wire removed. The coil is broken, so the element is replaced; no voltage reading is needed to reach that conclusion.
  • To read outlet voltage, set AC volts with the black lead in COM and the red lead in the V/Ω jack. The 10 A jack is a current path and would short a live outlet.

Check yourself

1. A 1,500 W portable heater is plugged into a 120 V circuit. Using Watt's law (P = E x I), how much current does the heater draw?

2. With power off and the element disconnected, a technician sets a digital multimeter to ohms and probes the two terminals of a dryer heating element. The display reads OL. What does this reading mean?

Facts checked 2026-11-15 · Sources: NAAEI: Certificate for Apartment Maintenance Technicians (CAMT), OSHA 29 CFR 1910.147: Control of hazardous energy (lockout/tagout)

CAMT Apartment Maintenance cheat sheet: every key fact on one page →