Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/32 ▾
  1. 1.Electrical Maintenance & Repair0/4
    1. Overloads, short circuits and ground faults
    2. Wiring receptacles, switches and fixtures
    3. Working safely: de-energize, test, then touch
    4. Ohm's law, Watt's law and the multimeter
  2. 2.Plumbing Maintenance & Repair0/4
    1. Supply, distribution and drainage: traps and vents
    2. Shutoffs, leaks and water damage
    3. Toilets, faucets and clearing drains
    4. Water heaters and joining pipe
  3. 3.HVAC Service & When to Refer0/5
    1. Airflow: filters, returns, registers and coils
    2. Condensate drains, pans and float switches
    3. Thermostats and controls
    4. The refrigeration cycle, superheat and EPA Section 608
    5. Furnaces, heat pumps, boilers and gas safety
  4. 4.Appliances, Locks & Keys0/5
    1. Refrigerators: moving heat out of the box
    2. Kitchen appliances: ranges, dishwashers, disposals and hoods
    3. Washers and dryers
    4. Reading schematics and testing parts
    5. Locks, keys and lockouts
  5. 5.Interior & Exterior Repair0/5
    1. Drywall repair
    2. Primer, paint and sheen
    3. Texture and caulk
    4. Doors, windows, cabinets and floors
    5. Exterior, ladders and suspect materials
  6. 6.Compliance, Safety & Fair Housing0/4
    1. Chemicals, PPE and sharps
    2. Lockout/tagout, confined spaces and ladders
    3. Fair housing in maintenance work
    4. Lead, asbestos, mold, pests and records
  7. 7.Facilities Operations & Professionalism0/5
    1. Prioritizing service requests and entering homes
    2. Make-ready turns, inspections and curb appeal
    3. Preventive maintenance, repair or replace, and contractors
    4. Pool and spa chemistry and math
    5. Life safety, reporting and records
Saved in this browser. Move it to another device →
← Electrical Maintenance & Repair

Chapter 1 · Lesson 1 of 4

Overloads, short circuits and ground faults

1 min read

Many electrical questions start with a breaker or a device that trips and ask what kind of fault caused it. Each fault has a different cause, a different protective device and a different correct response, so learn them as a set.

FaultWhat happensWhat responds
OverloadMore load than the circuit was designed to carryBreaker heats and trips after a delay
Short circuitCurrent takes an unintended, very low-resistance path back to the sourceBreaker trips at once
Ground faultCurrent leaks out of the circuit, for example through a person to a wet surfaceGFCI senses the imbalance and opens
Arc faultCurrent jumps a gap and makes heatAFCI recognizes the arcing pattern and opens

A GFCI compares the current going out on the hot conductor with the current coming back on the neutral. Pressing its TEST button creates a small imbalance on purpose, so a GFCI that does not trip when tested has failed and must be replaced.

One that will not reset with nothing plugged in means a fault is still on the wiring or the device itself is bad.

Example: a bathroom breaker trips again even after the resident moved a space heater to another circuit. Lowering the load did not help, so the breaker is reporting a fault. The technician looks for a short, a ground fault or a loose connection, and calls a licensed electrician if the cause cannot be found.

Check yourself

1. A resident reports a tingle when touching a plugged-in hair dryer while standing at a wet sink. Which condition is MOST likely present, and which device is designed to sense it?

2. A kitchen circuit breaker has tripped three times in one week. The technician has already moved two plug-in appliances to another circuit and it tripped again. What should the technician do NEXT?

Facts checked 2026-11-15 · Sources: NAAEI: Certificate for Apartment Maintenance Technicians (CAMT), OSHA 29 CFR 1910.147: Control of hazardous energy (lockout/tagout)

CAMT Apartment Maintenance cheat sheet: every key fact on one page →