Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/32 ▾

0 of 32 lessons finished

Continue: Primer, paint and sheen
  1. 1.Electrical Maintenance & Repair0/4
    1. Overloads, short circuits and ground faults
    2. Wiring receptacles, switches and fixtures
    3. Working safely: de-energize, test, then touch
    4. Ohm's law, Watt's law and the multimeter
  2. 2.Plumbing Maintenance & Repair0/4
    1. Supply, distribution and drainage: traps and vents
    2. Shutoffs, leaks and water damage
    3. Toilets, faucets and clearing drains
    4. Water heaters and joining pipe
  3. 3.HVAC Service & When to Refer0/5
    1. Airflow: filters, returns, registers and coils
    2. Condensate drains, pans and float switches
    3. Thermostats and controls
    4. The refrigeration cycle, superheat and EPA Section 608
    5. Furnaces, heat pumps, boilers and gas safety
  4. 4.Appliances, Locks & Keys0/5
    1. Refrigerators: moving heat out of the box
    2. Kitchen appliances: ranges, dishwashers, disposals and hoods
    3. Washers and dryers
    4. Reading schematics and testing parts
    5. Locks, keys and lockouts
  5. 5.Interior & Exterior Repair0/5
    1. Drywall repair
    2. Primer, paint and sheen
    3. Texture and caulk
    4. Doors, windows, cabinets and floors
    5. Exterior, ladders and suspect materials
  6. 6.Compliance, Safety & Fair Housing0/4
    1. Chemicals, PPE and sharps
    2. Lockout/tagout, confined spaces and ladders
    3. Fair housing in maintenance work
    4. Lead, asbestos, mold, pests and records
  7. 7.Facilities Operations & Professionalism0/5
    1. Prioritizing service requests and entering homes
    2. Make-ready turns, inspections and curb appeal
    3. Preventive maintenance, repair or replace, and contractors
    4. Pool and spa chemistry and math
    5. Life safety, reporting and records
Saved in this browser. Move it to another device →
← Interior & Exterior Repair

Chapter 5 · Lesson 1 of 5

Drywall repair

1 min read

Drywall questions test whether the repair removes the cause or just covers it. A nail pops because the fastener has worked loose from the framing, so driving it back down sets up the same failure.

The fix is to drive new screws into the stud on each side of the pop, pull the loose nail, then dimple, fill, sand, prime and paint. A crushed metal corner bead can no longer give a straight edge, so the damaged length is cut out and a new piece fastened in before the corner is coated and feathered.

  • Apply compound over a patch in thin coats, each feathered out past the last. One thick coat shrinks, cracks and leaves a bump.
  • A hole too large for a self-adhesive patch is cut square, wood backing is screwed behind it, and the new piece is fastened to that backing.
  • Joint compound spreads and sands easily but shrinks and dries slowly; spackle dries fast with little shrinkage but is for small holes and dents.

Example: a doorknob has punched a fist-sized hole in a hallway wall. The technician cuts the damage back to a clean rectangle, screws a strip of wood inside the opening as backing, fastens a matching piece of wallboard to it, tapes the seams, and finishes with three thin coats, each wider than the last.

Check yourself

1. A row of drywall nails on a bedroom wall has popped, cracking the paint over each head. What is the correct repair?

2. How do premixed (ready-mixed) joint compound and spackling compound differ when a technician has to choose between them?

Facts checked 2026-11-15 · Sources: NAAEI: Certificate for Apartment Maintenance Technicians (CAMT), EPA: Protect your family from exposures to asbestos

CAMT Apartment Maintenance cheat sheet: every key fact on one page →