Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/32 ▾

0 of 32 lessons finished

Continue: Texture and caulk
  1. 1.Electrical Maintenance & Repair0/4
    1. Overloads, short circuits and ground faults
    2. Wiring receptacles, switches and fixtures
    3. Working safely: de-energize, test, then touch
    4. Ohm's law, Watt's law and the multimeter
  2. 2.Plumbing Maintenance & Repair0/4
    1. Supply, distribution and drainage: traps and vents
    2. Shutoffs, leaks and water damage
    3. Toilets, faucets and clearing drains
    4. Water heaters and joining pipe
  3. 3.HVAC Service & When to Refer0/5
    1. Airflow: filters, returns, registers and coils
    2. Condensate drains, pans and float switches
    3. Thermostats and controls
    4. The refrigeration cycle, superheat and EPA Section 608
    5. Furnaces, heat pumps, boilers and gas safety
  4. 4.Appliances, Locks & Keys0/5
    1. Refrigerators: moving heat out of the box
    2. Kitchen appliances: ranges, dishwashers, disposals and hoods
    3. Washers and dryers
    4. Reading schematics and testing parts
    5. Locks, keys and lockouts
  5. 5.Interior & Exterior Repair0/5
    1. Drywall repair
    2. Primer, paint and sheen
    3. Texture and caulk
    4. Doors, windows, cabinets and floors
    5. Exterior, ladders and suspect materials
  6. 6.Compliance, Safety & Fair Housing0/4
    1. Chemicals, PPE and sharps
    2. Lockout/tagout, confined spaces and ladders
    3. Fair housing in maintenance work
    4. Lead, asbestos, mold, pests and records
  7. 7.Facilities Operations & Professionalism0/5
    1. Prioritizing service requests and entering homes
    2. Make-ready turns, inspections and curb appeal
    3. Preventive maintenance, repair or replace, and contractors
    4. Pool and spa chemistry and math
    5. Life safety, reporting and records
Saved in this browser. Move it to another device →
← Interior & Exterior Repair

Chapter 5 · Lesson 2 of 5

Primer, paint and sheen

1 min read

Paint questions turn on preparation. Bare joint compound is much more porous than the painted wall around it, so it soaks up binder from the topcoat and the spot dries duller and slightly off in color. Priming the patch evens out that porosity.

A water stain is different: its residues dissolve in water-based coatings and bleed right back through, so extra coats of latex paint or an ordinary latex primer will not stop it. A stain-blocking sealer forms a barrier the stain cannot pass.

  • Old glossy enamel is cleaned and then sanded or chemically dulled so the new coat can grip. Grease and soap film act as bond breakers.
  • Walls that are washed often, such as kitchens, get semi-gloss or gloss, whose harder film takes repeated cleaning. Flat paint burnishes where it is scrubbed.
  • If a spot-painted patch still stands out, roll the whole wall from corner to corner for one uniform film.

Example: a hallway ceiling still shows a brown ring after the roof leak above it was fixed and two coats of flat white were rolled on. The technician spot-coats the ring with a stain-blocking sealer, lets it dry, and then rolls the finish coat over the whole ceiling so the sheen stays even.

Check yourself

1. The roof leak has been repaired, but a brown water stain still bleeds through two coats of flat ceiling paint. What should be applied?

2. Why must a fresh compound patch be primed before the finish coat is applied?

Facts checked 2026-11-15 · Sources: NAAEI: Certificate for Apartment Maintenance Technicians (CAMT), EPA: Protect your family from exposures to asbestos

CAMT Apartment Maintenance cheat sheet: every key fact on one page →